kernel.git/drivers/mmc/core/core.c, branch linux-4.19.y

mmc: block: Be sure to wait while busy in CQE error recovery

2023-12-20T14:38:04Z

commit c616696a902987352426fdaeec1b0b3240949e6b upstream. STOP command does not guarantee to wait while busy, but subsequent command MMC_CMDQ_TASK_MGMT to discard the queue will fail if the card is busy, so be sure to wait by employing mmc_poll_for_busy(). Fixes: 72a5af554df8 ("mmc: core: Add support for handling CQE requests") Cc: stable@vger.kernel.org Signed-off-by: Adrian Hunter Reviewed-by: Avri Altman Reviewed-by: Christian Loehle Link: https://lore.kernel.org/r/20231103084720.6886-4-adrian.hunter@intel.com Signed-off-by: Ulf Hansson Tested-by: Adrian Hunter Signed-off-by: Adrian Hunter Signed-off-by: Greg Kroah-Hartman

mmc: block: Retry commands in CQE error recovery

2023-12-08T07:43:26Z

[ Upstream commit 8155d1fa3a747baad5caff5f8303321d68ddd48c ] It is important that MMC_CMDQ_TASK_MGMT command to discard the queue is successful because otherwise a subsequent reset might fail to flush the cache first. Retry it and the previous STOP command. Fixes: 72a5af554df8 ("mmc: core: Add support for handling CQE requests") Cc: stable@vger.kernel.org Signed-off-by: Adrian Hunter Reviewed-by: Avri Altman Link: https://lore.kernel.org/r/20231103084720.6886-5-adrian.hunter@intel.com Signed-off-by: Ulf Hansson Signed-off-by: Sasha Levin

mmc: core: convert comma to semicolon

2023-12-08T07:43:26Z

[ Upstream commit 6b1dc6229aecbcb45e8901576684a8c09e25ad7b ] Replace a comma between expression statements by a semicolon. Signed-off-by: Zheng Yongjun Link: https://lore.kernel.org/r/20201216131737.14883-1-zhengyongjun3@huawei.com Signed-off-by: Ulf Hansson Stable-dep-of: 8155d1fa3a74 ("mmc: block: Retry commands in CQE error recovery") Signed-off-by: Sasha Levin

mmc: core: properly select voltage range without power cycle

2022-11-25T16:40:27Z

commit 39a72dbfe188291b156dd6523511e3d5761ce775 upstream. In mmc_select_voltage(), if there is no full power cycle, the voltage range selected at the end of the function will be on a single range (e.g. 3.3V/3.4V). To keep a range around the selected voltage (3.2V/3.4V), the mask shift should be reduced by 1. This issue was triggered by using a specific SD-card (Verbatim Premium 16GB UHS-1) on an STM32MP157C-DK2 board. This board cannot do UHS modes and there is no power cycle. And the card was failing to switch to high-speed mode. When adding the range 3.2V/3.3V for this card with the proposed shift change, the card can switch to high-speed mode. Fixes: ce69d37b7d8f ("mmc: core: Prevent violation of specs while initializing cards") Signed-off-by: Yann Gautier Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20221028073740.7259-1-yann.gautier@foss.st.com Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc: core: clear flags before allowing to retune

2021-07-20T14:16:04Z

commit 77347eda64ed5c9383961d1de9165f9d0b7d8df6 upstream. It might be that something goes wrong during tuning so the MMC core will immediately trigger a retune. In our case it was: - we sent a tuning block - there was an error so we need to send an abort cmd to the eMMC - the abort cmd had a CRC error - retune was set by the MMC core This lead to a vicious circle causing a performance regression of 75%. So, clear retuning flags before we enable retuning to start with a known cleared state. Reported-by Yoshihiro Shimoda Suggested-by: Adrian Hunter Signed-off-by: Wolfram Sang Acked-by: Adrian Hunter Reviewed-by: Yoshihiro Shimoda Tested-by: Yoshihiro Shimoda Fixes: bd11e8bd03ca ("mmc: core: Flag re-tuning is needed on CRC errors") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210624151616.38770-2-wsa+renesas@sang-engineering.com Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc: core: Do a power cycle when the CMD11 fails

2021-05-22T08:59:13Z

commit 147186f531ae49c18b7a9091a2c40e83b3d95649 upstream. A CMD11 is sent to the SD/SDIO card to start the voltage switch procedure into 1.8V I/O. According to the SD spec a power cycle is needed of the card, if it turns out that the CMD11 fails. Let's fix this, to allow a retry of the initialization without the voltage switch, to succeed. Note that, whether it makes sense to also retry with the voltage switch after the power cycle is a bit more difficult to know. At this point, we treat it like the CMD11 isn't supported and therefore we skip it when retrying. Signed-off-by: DooHyun Hwang Link: https://lore.kernel.org/r/20210210045936.7809-1-dh0421.hwang@samsung.com Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc: core: Respect MMC_CAP_NEED_RSP_BUSY for erase/trim/discard

2020-04-02T13:28:09Z

[ Upstream commit 43cc64e5221cc6741252b64bc4531dd1eefb733d ] The busy timeout that is computed for each erase/trim/discard operation, can become quite long and may thus exceed the host->max_busy_timeout. If that becomes the case, mmc_do_erase() converts from using an R1B response to an R1 response, as to prevent the host from doing HW busy detection. However, it has turned out that some hosts requires an R1B response no matter what, so let's respect that via checking MMC_CAP_NEED_RSP_BUSY. Note that, if the R1B gets enforced, the host becomes fully responsible of managing the needed busy timeout, in one way or the other. Suggested-by: Sowjanya Komatineni Cc: Tested-by: Anders Roxell Tested-by: Sowjanya Komatineni Tested-by: Faiz Abbas Tested-By: Peter Geis Signed-off-by: Ulf Hansson Signed-off-by: Sasha Levin

mmc: core: API to temporarily disable retuning for SDIO CRC errors

2019-06-25T03:35:53Z

commit 0a55f4ab9678413a01e740c86e9367ba0c612b36 upstream. Normally when the MMC core sees an "-EILSEQ" error returned by a host controller then it will trigger a retuning of the card. This is generally a good idea. However, if a command is expected to sometimes cause transfer errors then these transfer errors shouldn't cause a re-tuning. This re-tuning will be a needless waste of time. One example case where a transfer is expected to cause errors is when transitioning between idle (sometimes referred to as "sleep" in Broadcom code) and active state on certain Broadcom WiFi SDIO cards. Specifically if the card was already transitioning between states when the command was sent it could cause an error on the SDIO bus. Let's add an API that the SDIO function drivers can call that will temporarily disable the auto-tuning functionality. Then we can add a call to this in the Broadcom WiFi driver and any other driver that might have similar needs. NOTE: this makes the assumption that the card is already tuned well enough that it's OK to disable the auto-retuning during one of these error-prone situations. Presumably the driver code performing the error-prone transfer knows how to recover / retry from errors. ...and after we can get back to a state where transfers are no longer error-prone then we can enable the auto-retuning again. If we truly find ourselves in a case where the card needs to be retuned sometimes to handle one of these error-prone transfers then we can always try a few transfers first without auto-retuning and then re-try with auto-retuning if the first few fail. Without this change on rk3288-veyron-minnie I periodically see this in the logs of a machine just sitting there idle: dwmmc_rockchip ff0d0000.dwmmc: Successfully tuned phase to XYZ Cc: stable@vger.kernel.org #v4.18+ Signed-off-by: Douglas Anderson Acked-by: Adrian Hunter Acked-by: Kalle Valo Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc:fix a bug when max_discard is 0

2019-03-23T19:09:57Z

commit d4721339dcca7def04909a8e60da43c19a24d8bf upstream. The original purpose of the code I fix is to replace max_discard with max_trim if max_trim is less than max_discard. When max_discard is 0 we should replace max_discard with max_trim as well, because max_discard equals 0 happens only when the max_do_calc_max_discard process is overflowed, so if mmc_can_trim(card) is true, max_discard should be replaced by an available max_trim. However, in the original code, there are two lines of code interfere the right process. 1) if (max_discard && mmc_can_trim(card)) when max_discard is 0, it skips the process checking if max_discard needs to be replaced with max_trim. 2) if (max_trim < max_discard) the condition is false when max_discard is 0. it also skips the process that replaces max_discard with max_trim, in fact, we should replace the 0-valued max_discard with max_trim. Signed-off-by: Jiong Wu Fixes: b305882fbc87 (mmc: core: optimize mmc_calc_max_discard) Cc: stable@vger.kernel.org # v4.17+ Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc: core: Fix NULL ptr crash from mmc_should_fail_request

2019-03-05T16:58:53Z

commit e5723f95d6b493dd437f1199cacb41459713b32f upstream. In case of CQHCI, mrq->cmd may be NULL for data requests (non DCMD). In such case mmc_should_fail_request is directly dereferencing mrq->cmd while cmd is NULL. Fix this by checking for mrq->cmd pointer. Fixes: 72a5af554df8 ("mmc: core: Add support for handling CQE requests") Signed-off-by: Ritesh Harjani Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman