kernel.git/drivers/mmc/core/core.c, branch linux-2.6.31.y

MMC core: limit minimum initialization frequency to 400kHz

2009-06-13T20:42:57Z

Some controllers allow a much lower frequency than 400kHz. Keep the minimum frequency within sensible limits. Signed-off-by: Sascha Hauer

mmc: mmc_rescan detects card change in one run

2009-06-13T20:42:56Z

With this patch, mmc_rescan can detect the removal of an mmc card and the insertion of (possibly another) card in the same run. This means that a card change can be detected without having to call mmc_detect_change multiple times. This change generalises the core such that it can be easily used by hosts which provide a mechanism to detect only the presence of a card reader cover, which has to be taken off in order to insert a card. Other hosts ("card detect" or "MMC_CAP_NEEDS_POLL") each receive an event when a card is removed and when a card is inserted, so it is sufficient for them if mmc_rescan handles only one event at a time. "Cover detect" hosts, however, only receive events about the cover status. This means that between 2 subsequent events, both a card removal and a card insertion can occur. In this case, the pre-patch version of mmc_rescan would only detect the removal of the previous card but not the insertion of the new card. Signed-off-by: Jorg Schummer Signed-off-by: Pierre Ossman

mmc: increase power up delay

2009-05-03T20:11:31Z

The TI controller on Toshiba Tecra M5 needs more time to power up or the cards will init incorrectly or not at all. Signed-off-by: José M. Fernández Signed-off-by: Pierre Ossman

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc

2009-04-05T17:18:21Z

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (42 commits) atmel-mci: fix sdc_reg typo tmio_mmc: add maintainer mmc: Add OpenFirmware bindings for SDHCI driver sdhci: Add quirk for forcing maximum block size to 2048 bytes sdhci: Add quirk for controllers that need IRQ re-init after reset sdhci: Add quirk for controllers that need small delays for PIO sdhci: Add set_clock callback and a quirk for nonstandard clocks sdhci: Add get_{max,timeout}_clock callbacks sdhci: Add support for hosts reporting inverted write-protect state sdhci: Add support for card-detection polling sdhci: Enable only relevant (DMA/PIO) interrupts during transfers sdhci: Split card-detection IRQs management from sdhci_init() sdhci: Add support for bus-specific IO memory accessors mmc_spi: adjust for delayed data token response omap_hsmmc: Wait for SDBP omap_hsmmc: Fix MMC3 dma omap_hsmmc: Disable SDBP at suspend omap_hsmmc: Do not prefix slot name omap_hsmmc: Allow cover switch to cause rescan omap_hsmmc: Add 8-bit bus width mode support ...

MMC: regulator utilities

2009-03-31T08:56:26Z

Glue between MMC and regulator stacks ... verified with some OMAP3 boards using adjustable and configured-as-fixed regulators on several MMC controllers. These calls are intended to be used by MMC host adapters using at least one regulator per host. Examples include slots with regulators supporting multiple voltages and ones using multiple voltage rails (e.g. DAT4..DAT7 using a separate supply, or a split rail chip like certain SDIO WLAN or eMMC solutions). Signed-off-by: David Brownell Acked-by: Pierre Ossman Signed-off-by: Liam Girdwood

mmc_spi: allow higher timeouts for SPI mode

2009-03-24T20:30:02Z

Some SD cards have very high timeouts in SPI mode. So adjust the timeouts from theory to practice. Signed-off-by: Wolfgang Muees Acked-by: David Brownell Signed-off-by: Pierre Ossman

mmc: During unsafe resume, select the right volatge for the card

2009-03-24T20:30:01Z

During mmc unsafe resume, choose the right voltage for the card after powerup. Although this has not seen to cause trouble, it's the wrong behaviour. Signed-off-by: Balaji Rao Signed-off-by: Pierre Ossman

mmc: delayed_work was never cancelled

2009-03-24T20:29:58Z

The delayed work item mmc_host.detect is now cancelled before flushing the work queue. This takes care of cases when delayed_work was scheduled for mmc_host.detect, but not yet placed in the work queue. Signed-off-by: Jorg Schummer Signed-off-by: Pierre Ossman

mmc: warn about voltage mismatches

2008-12-31T18:27:18Z

Get rid of a silent failure mode when the MMC/SD host doesn't support the voltages needed to operate a given card, by adding a warning. A 3.3V host and a 3.0V card, for example, no longer need to mysteriously just not work at all. This isn't the best diagnostic; ideally it would also tell what voltage the card and host support (and not just by dumping the bitmasks). Signed-off-by: David Brownell Signed-off-by: Pierre Ossman

mmc: Add mmc_vddrange_to_ocrmask() helper function

2008-12-31T17:18:13Z

This function sets the OCR mask bits according to provided voltage ranges. Will be used by the mmc_spi OpenFirmware bindings. Signed-off-by: Anton Vorontsov Signed-off-by: Pierre Ossman