kernel.git/drivers/mmc/core/bus.c, branch linux-3.1.y

mmc: sd: report correct speed and capacity of uhs cards

2011-05-25T03:53:46Z

Since only UHS-I cards respond with S18A set in response to ACMD41, we set the card as ultra-high-speed after successfull initialization. We need to decide whether a card is SDXC based on the C_SIZE field of CSDv2.0 register. According to Physical Layer spec v3.01, the minimum value of C_SIZE for SDXC card is 00FFFFh. Tested by Zhangfei Gao with a Toshiba uhs card and general hs card, on mmp2 in SDMA mode. Signed-off-by: Arindam Nath Reviewed-by: Philip Rakity Tested-by: Philip Rakity Acked-by: Zhangfei Gao Signed-off-by: Chris Ball

mmc: core: mmc_add_card(): fix missing break in switch statement

2011-04-27T23:15:07Z

Fixes a cosmetic bug that affects printk() for SD-combo cards. Reported-by: Prashanth Bhat Signed-off-by: Michał Mirosław Signed-off-by: Chris Ball

mmc: Register debugfs dir before calling card probe function.

2011-01-09T04:52:26Z

This way, the probe function may register debugfs files if it wants to. This fixes a bug with mmc_test where mmc_test_register_file_test() is called before the card's debugfs dir exists, and so it fails. Signed-off-by: Viresh Kumar Tested-by: Chris Ball Signed-off-by: Chris Ball

mmc: add runtime PM handlers

2010-10-23T13:11:18Z

Add MMC runtime PM handlers, which call mmc_power_save_host and mmc_power_restore_host in response to runtime_suspend and runtime_resume events. Runtime PM is still disabled by default, so this patch alone has no immediate effect. Signed-off-by: Ohad Ben-Cohen Tested-by: Luciano Coelho Signed-off-by: Chris Ball

mmc: Fixes for Dual Data Rate (DDR) support

2010-10-23T13:11:16Z

The DDR support patch needs the following fixes: - The block driver does not need to know about DDR, any more than it needs to know about bus width. - Not only the card must be switched to DDR mode. The host controller must also be configured, which is done through the 'set_ios()' function. - Do not set the DDR mode state until after the switch command is successful. - Setting block length is not supported in DDR mode. Make that a core function and change the other place it is used (mmc_test) also. Signed-off-by: Adrian Hunter Signed-off-by: Chris Ball

mmc: rename dev_to_mmc_card() to mmc_dev_to_card()

2010-10-23T13:11:12Z

Global symbols should use their subsystem name in a prefixed fashion. Signed-off-by: Andy Shevchenko Cc: Signed-off-by: Andrew Morton Signed-off-by: Chris Ball

mmc: make mmc_dev_to_card() macro public

2010-10-23T13:11:12Z

Conversion from struct device to struct mmc_card is used more than in one place. Due to this it's better to have public macro for such thing. Signed-off-by: Andy Shevchenko Cc: Adrian Hunter Cc: Signed-off-by: Andrew Morton Signed-off-by: Chris Ball

mmc: implement SD-combo (IO+mem) support

2010-08-11T15:59:03Z

Signed-off-by: Michal Miroslaw Cc: Adrian Hunter Cc: Chris Ball Cc: Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

2010-03-30T13:02:32Z

percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo Guess-its-ok-by: Christoph Lameter Cc: Ingo Molnar Cc: Lee Schermerhorn

mmc: add MODALIAS linkage for MMC/SD devices

2009-03-24T20:29:58Z

Currently we are using an explicit udev rule to trigger loading of the mmc-block module when an MMC or SD card is detected: SUBSYSTEM=="mmc", RUN+="/sbin/modprobe -Qba mmc-block" It makes much more sense for the mmc bus driver and the mmc-block module to share MODALIAS information so that they are linked automatically. There is no real information of use in the MMC system at the current time. All devices inserted require us to load the mmc-block device. Until such time as useful parameters exist simply reflect the module linkage via the module alias below: mmc:block Signed-off-by: Andy Whitcroft Signed-off-by: Pierre Ossman