kernel.git/drivers/media/usb/dvb-usb, branch linux-3.17.y

[media] Fix typo in comments

2014-07-26T18:09:47Z

Expression ((7bit i2c_addr << 1) & 0x01) can not be right because it is always 0 Signed-off-by: Raimonds Cicans Signed-off-by: Mauro Carvalho Chehab

[media] Fix regression in some dib0700 based devices

2014-07-26T03:51:02Z

Fix regression in some dib0700 based devices. Set size_of_priv, and don't call dvb_detach unnecessarily. This resolves the oops(s) for my "Leadtek Winfast DTV Dongle (STK7700P based)" Signed-off-by: James Harper Signed-off-by: Mauro Carvalho Chehab

[media] rc-core: remove protocol arrays

2014-07-25T22:10:43Z

The basic API of rc-core used to be: dev = rc_allocate_device(); dev->x = a; dev->y = b; dev->z = c; rc_register_device(); which is a pretty common pattern in the kernel, after the introduction of protocol arrays the API looks something like: dev = rc_allocate_device(); dev->x = a; rc_set_allowed_protocols(dev, RC_BIT_X); dev->z = c; rc_register_device(); There's no real need for the protocols to be an array, so change it back to be consistent (and in preparation for the following patches). [m.chehab@samsung.com: added missing changes at some files] Signed-off-by: David Härdeman Signed-off-by: Mauro Carvalho Chehab

[media] rc-core: document the protocol type

2014-07-24T00:50:48Z

Right now the protocol information is not preserved, rc-core gets handed a scancode but has no idea which protocol it corresponds to. This patch (which required reading through the source/keymap for all drivers, not fun) makes the protocol information explicit which is important documentation and makes it easier to e.g. support multiple protocols with one decoder (think rc5 and rc-streamzap). The information isn't used yet so there should be no functional changes. [m.chehab@samsung.com: rebased, added cxusb and removed bad whitespacing] Signed-off-by: David Härdeman Signed-off-by: Mauro Carvalho Chehab

[media] dib0700: NEC scancode cleanup

2014-07-24T00:26:08Z

the RC RX packet is defined as: struct dib0700_rc_response { ... u8 not_system; u8 system; ... u8 data; u8 not_data; The NEC protocol transmits in the order: system not_system data not_data Note that the code defines the NEC extended scancode as: scancode = be16_to_cpu(poll_reply->system16) << 8 | poll_reply->data; i.e. scancode = poll_reply->not_system << 16 | poll_reply->system << 8 | poll_reply->data; Which, if the order *is* reversed, would mean that the scancode that gets defined is in reality: scancode = poll_reply->system << 16 | poll_reply->not_system << 8 | poll_reply->data; Which is the same as the order used in drivers/media/rc/ir-nec-decoder.c. This patch changes the code to match my assumption (the generated scancode should, however, not change). [m.chehab@samsung.com: rebased and fixed the decoding error message] Signed-off-by: David Härdeman CC: Patrick Boettcher Tested-by: Mauro Carvalho Chehab Signed-off-by: Mauro Carvalho Chehab

[media] cxusb: increase buffer length to 80 bytes

2014-07-23T00:58:23Z

As reported by Vincent: [ 16.332247] xc2028 0-0061: Loading firmware for type=BASE F8MHZ (3), id 0000000000000000. [ 16.344378] cxusb: i2c wr: len=64 is too big! 64 bytes is too short for firmware load on this device. So, increase it to 80 bytes. Reported-by: Vincent McIntyre Signed-off-by: Mauro Carvalho Chehab

[media] dw2102: Geniatech T220 init fixed

2014-07-22T12:48:12Z

Geniatech T220 init fixed - reset cmd from windows driver and fixed TS bus config for cxd2820r. Signed-off-by: Evgeny Plehov Signed-off-by: Mauro Carvalho Chehab

[media] cxusb: Prepare for si2157 driver getting more parameters

2014-07-22T00:28:10Z

Modify all users of si2157_config to correctly initialize all not listed values to 0. Signed-off-by: Matthias Schwarzott Signed-off-by: Antti Palosaari Signed-off-by: Mauro Carvalho Chehab

[media] cxusb: TechnoTrend CT2-4400 USB DVB-T2/C tuner support

2014-07-15T00:07:07Z

USB ID 0b48:3014. USB interface: Cypress CY7C68013A-56LTXC Demodulator: Silicon Labs Si2168-30 Tuner: Silicon Labs Si2158-20 Cc: Michael Krufky Signed-off-by: Olli Salonen Reviewed-by: Antti Palosaari Signed-off-by: Antti Palosaari Reviewed-by: Michael Ira Krufky Signed-off-by: Mauro Carvalho Chehab

[media] dib0700: better document struct init

2014-07-07T12:56:37Z

Instead of using anonymous initialization for dib0896 structs, identify each field by name. That helps to understand what's being initialized. No functional changes. Acked-By: Patrick Boettcher Signed-off-by: Mauro Carvalho Chehab