kernel.git/drivers/media/rc, branch linux-3.17.y

media: rc-core: fix toggle handling in the rc6 decoder

2014-12-16T17:37:08Z

commit d2a74581390d8e5ed09b12c9d4736847d918dfa6 upstream. The toggle bit shouldn't be cleared before the toggle value is calculated. This should probably go into 3.17.x as well. Fixes: 120703f9eb32 ([media] rc-core: document the protocol type) Tested-by: Stephan Raue Signed-off-by: David Härdeman Signed-off-by: Mauro Carvalho Chehab Signed-off-by: Greg Kroah-Hartman

media: rc-core: fix protocol_change regression in ir_raw_event_register

2014-11-14T18:10:28Z

commit 14edb593338e3811e818aba286237c365f8881a1 upstream. IR receiver using nuvoton-cir and lirc required additional configuration steps after upgrade from kernel 3.16 to 3.17-rcX. Bisected regression to commit da6e162d6a4607362f8478c715c797d84d449f8b ("[media] rc-core: simplify sysfs code"). The regression comes from adding function change_protocol in ir-raw.c. It changes behaviour so that only the protocol enabled by driver's map_name will be active after registration. This breaks user space behaviour, lirc does not get key press signals anymore. Enable lirc protocol by default for ir raw decoders to restore original behaviour. Signed-off-by: Tomas Melin Acked-by: David Härdeman Signed-off-by: Mauro Carvalho Chehab Signed-off-by: Greg Kroah-Hartman

media: imon: fix other RC type protocol support

2014-11-14T18:10:27Z

commit d358aefdc0cc92b16ced449f998dbad639db6809 upstream. With kernel 3.17 the imon remote control for device 15c2:0034 does not work anymore, which uses the OTHER protocol. Only the front panel buttons which uses the RC6 protocol are working. Adds the missing comparison for the RC_BIT_OTHER. Signed-off-by: Ulrich Eckhardt Signed-off-by: Mauro Carvalho Chehab Signed-off-by: Greg Kroah-Hartman

[media] ir-rc5-decoder: print where decoding fails

2014-07-30T18:49:35Z

The IR dprintk message that prints a RC5 decoding failure is not much helpful, as it doesn't tell on what bit the error occurred. Add such information, in order to make the debug message more useful. Signed-off-by: Mauro Carvalho Chehab

[media] rc-main: allow raw protocol drivers to restrict the allowed protos

2014-07-30T18:45:48Z

On some hardware (au0828/au8522), the hardware is broken with regards to the initial pulse detection. So, the driver needs to produce a fake start pulse. That limits the acceptable protocols, as it is not possible to produce a fake pulse that would cover all supported protocols. So, allow the driver to explicitly set the allowed protocols. If the driver doesn't specify, keep the old behavior. Signed-off-by: Mauro Carvalho Chehab

[media] mceusb: select default keytable based on vendor

2014-07-27T20:37:01Z

Some vendors have their on keymap table that are used on all (or almost all) models for that vendor. So, instead of specifying the keymap table per USB ID, let's use the Vendor ID's table by default. At the end, this will mean less code to be added when newer devices for those vendors are added. Of course, if rc_map is specified per board, it takes precedence. Signed-off-by: Mauro Carvalho Chehab

[media] mceusb: add support for newer cx231xx devices

2014-07-27T20:13:53Z

Add support for the si2165-based cx231xx devices: [2013:025e] PCTV QuatroStick 522e [2013:0259] PCTV QuatroStick 521e [2040:b131] Hauppauge WinTV 930C-HD (model 1114xx) They're similar to the already supported: [2040:b130] Hauppauge WinTV 930C-HD (model 1113xx) Signed-off-by: Mauro Carvalho Chehab

[media] rc: Add support for decoding XMP protocol

2014-07-26T22:38:04Z

This protocol is found on Dreambox remotes [m.chehab@samsung.com: CodingStyle fixes and conflict fix] Signed-off-by: Marcel Mol Signed-off-by: Mauro Carvalho Chehab

[media] ati_remote: Better default keycodes

2014-07-26T02:59:06Z

This tries to make them more like other remotes, and/or the button labels. Notably, the (>>) button is made KEY_FASTFORWARD, which is the correct opposite of (<<)'s KEY_REVERSE. (It was KEY_FORWARD, something else entirely.) Likewise, KEY_STOP is the Sun keyboard "interrupt program" key; the media key is KEY_STOPCD. A restriction is that I try to avoid keycodes above 255, as the X11 client/server protocol is limited to 8-bit key codes. If not for this, I would have used the KEY_NUMERIC_x codes for the numbers. Signed-off-by: George Spelvin Signed-off-by: Mauro Carvalho Chehab

[media] ati_remote: Add comments to keycode table

2014-07-26T02:54:32Z

A more detailed description of what the buttons look like and their intended function makes it easier for people to maintain this code without access to the hardware. [m.chehab@samsung.com: Fixed a typo "Mdeia" instead of "Media"] Signed-off-by: George Spelvin Signed-off-by: Mauro Carvalho Chehab