kernel.git/drivers/media/rc/Makefile, branch linux-3.16.y

[media] rc: img-ir: add to build

2014-03-11T18:43:04Z

Add ImgTec IR decoder driver to the build system. Signed-off-by: James Hogan Signed-off-by: Mauro Carvalho Chehab

[media] media: rc: add raw decoder for Sharp protocol

2014-02-04T17:43:13Z

Add a raw decoder for the Sharp protocol. It uses a pulse distance modulation with a pulse of 320us and a bit period of 2ms for a logical 1 and 1ms for a logical 0. The first part of the message consists of a 5-bit address, an 8-bit command, and two other bits, followed by a 40ms gap before the echo message which is an inverted version of the main message except for the address bits. Signed-off-by: James Hogan Cc: Mauro Carvalho Chehab Cc: linux-media@vger.kernel.org Signed-off-by: Mauro Carvalho Chehab

[media] media: st-rc: Add ST remote control driver

2013-10-31T10:20:08Z

This patch adds support to ST RC driver, which is basically a IR/UHF receiver and transmitter. This IP (IRB) is common across all the ST parts for settop box platforms. IRB is embedded in ST COMMS IP block. It supports both Rx & Tx functionality. This driver adds only Rx functionality via LIRC codec. Signed-off-by: Srinivas Kandagatla Acked-by: Sean Young Signed-off-by: Mauro Carvalho Chehab

[media] media: rc: Introduce RX51 IR transmitter driver

2012-08-13T19:53:45Z

This is the driver for the IR transmitter diode found on the Nokia N900 (also known as RX51) device. The driver is mostly the same as found in the original 2.6.28 based kernel that comes with the device. The following modifications have been made compared to the original driver version: - Adopt to the changes that has happen in the kernel during the past five years, such as the change in the include paths - The OMAP DM-timers require much more care nowadays. The timers need to be enabled and disabled or otherwise many actions fail. Timers must not be freed without first stopping them or otherwise the timer cannot be requested again. The code has been tested with sending IR codes with N900 device running Debian userland. The device receiving the codes was Anysee DVB-C USB receiver. Signed-off-by: Timo Kokkonen Cc: Tony Lindgren Cc: linux-omap@vger.kernel.org Cc: Sakari Ailus Signed-off-by: Mauro Carvalho Chehab

[media] rc: Add support for the TechnoTrend USB IR Receiver

2012-08-13T19:19:11Z

This driver adds support for TechnoTrend USB IR Receiver. It is a complete rewrite of the staging/media/lirc/lirc_ttusbir driver. It adds more accurate sample reporting and led control. Signed-off-by: Sean Young Signed-off-by: Mauro Carvalho Chehab

[media] Add support for the IguanaWorks USB IR Transceiver

2012-07-31T00:53:49Z

Signed-off-by: Sean Young Signed-off-by: Mauro Carvalho Chehab

[media] rc: Add support for GPIO based IR Receiver driver

2012-03-08T14:14:10Z

Adds GPIO based IR Receiver driver. It decodes signals using decoders available in rc framework. Signed-off-by: Ravi Kumar V Signed-off-by: Mauro Carvalho Chehab

[media] rc: Add support for decoding Sanyo protocol

2011-11-23T21:23:10Z

This protocol is found on Sanyo/Aiwa remotes. Tested with an Aiwa RC-7AS06 remote control. Signed-off-by: Mauro Carvalho Chehab

[media] move ati_remote driver from input/misc to media/rc

2011-09-22T13:47:41Z

The driver will be migrated to the RC driver API in a following commit. [mchehab@redhat.com: Fix some bad whitespacing] Signed-off-by: Anssi Hannula Signed-off-by: Mauro Carvalho Chehab

[media] rc-core support for Microsoft IR keyboard/mouse

2011-07-27T20:55:59Z

This is a custom IR protocol decoder, for the RC-6-ish protocol used by the Microsoft Remote Keyboard, apparently developed internally at Microsoft, and officially dubbed MCIR-2, per their March 2011 remote and transceiver requirements and specifications document, which also touches on this IR keyboard/mouse device. Its a standard keyboard with embedded thumb stick mouse pointer and mouse buttons, along with a number of media keys. The media keys are standard RC-6, identical to the signals from the stock MCE remotes, and will be handled as such. The keyboard and mouse signals will be decoded and delivered to the system by an input device registered specifically by this driver. Successfully tested with multiple mceusb-driven transceivers, as well as with fintek-cir and redrat3 hardware. Essentially, any raw IR hardware with enough sampling resolution should be able to use this decoder, nothing about it is at all receiver-hardware-specific. This work is inspired by lirc_mod_mce: The documentation there and code aided in understanding and decoding the protocol, but the bulk of the code is actually borrowed more from the existing in-kernel decoders than anything. I did recycle the keyboard keycode table, a few defines, and some of the keyboard and mouse data parsing bits from lirc_mod_mce though. Special thanks to James Meyer for providing the hardware, and being patient with me as I took forever to get around to writing this. callback routine to ensure we don't get any stuck keys, and used symbolic names for the keytable. Also cc'ing Florian this time, who I believe is the original mod-mce author... CC: Florian Demski Signed-off-by: Jarod Wilson Signed-off-by: Mauro Carvalho Chehab