kernel.git/drivers/media/platform/sunxi, branch linux-5.5.y

media: sun4i-csi: Fix [HV]sync polarity handling

2020-02-24T07:38:03Z

[ Upstream commit 1948dcf0f928b8bcdca57ca3fba8545ba380fc29 ] The Allwinner camera sensor interface has a different definition of [HV]sync. While the timing diagram uses the names HSYNC and VSYNC, the note following the diagram and register names use HREF and VREF. Combined they imply the hardware uses either [HV]REF or inverted [HV]SYNC. There are also registers to set horizontal skip lengths in pixels and vertical skip lengths in lines, also known as back porches. Fix the polarity handling by using the opposite polarity flag for the checks. Also rename `[hv]sync_pol` to `[hv]ref_pol` to better match the hardware register description. Fixes: 577bbf23b758 ("media: sunxi: Add A10 CSI driver") Signed-off-by: Chen-Yu Tsai Acked-by: Maxime Ripard Signed-off-by: Sakari Ailus Signed-off-by: Mauro Carvalho Chehab Signed-off-by: Sasha Levin

media: sun4i-csi: Fix data sampling polarity handling

2020-02-24T07:38:02Z

[ Upstream commit cf9e6d5dbdd56ef2aa72f28c806711c4293c8848 ] The CLK_POL field specifies whether data is sampled on the falling or rising edge of PCLK, not whether the data lines are active high or low. Evidence of this can be found in the timing diagram labeled "horizontal size setting and pixel clock timing". Fix the setting by checking the correct flag, V4L2_MBUS_PCLK_SAMPLE_RISING. While at it, reorder the three polarity flag checks so HSYNC and VSYNC are grouped together. Fixes: 577bbf23b758 ("media: sunxi: Add A10 CSI driver") Signed-off-by: Chen-Yu Tsai Acked-by: Maxime Ripard Signed-off-by: Sakari Ailus Signed-off-by: Mauro Carvalho Chehab Signed-off-by: Sasha Levin

media: sun4i-csi: Deal with DRAM offset

2020-02-24T07:38:02Z

[ Upstream commit 249b286171fa9c358e8d5c825b48c4ebea97c498 ] On Allwinner SoCs, some high memory bandwidth devices do DMA directly over the memory bus (called MBUS), instead of the system bus. These devices include the CSI camera sensor interface, video (codec) engine, display subsystem, etc.. The memory bus has a different addressing scheme without the DRAM starting offset. Deal with this using the "interconnects" property from the device tree, or if that is not available, set dev->dma_pfn_offset to PHYS_PFN_OFFSET. Fixes: 577bbf23b758 ("media: sunxi: Add A10 CSI driver") Signed-off-by: Chen-Yu Tsai Acked-by: Maxime Ripard Signed-off-by: Sakari Ailus Signed-off-by: Mauro Carvalho Chehab Signed-off-by: Sasha Levin

media: sun4i: Add H3 deinterlace driver

2019-10-24T22:07:59Z

Allwinner H3 SoC contains deinterlace unit, which has several modes of operation - bypass, weave, bob and mixed (advanced) mode. I don't know how mixed mode works, but according to Allwinner it gives best results, so they use it exclusively. Currently this mode is also hardcoded here. For each interleaved frame queued, this driver produces 2 deinterlaced frames. Deinterlaced frames are based on 2 consequtive output buffers, except for the first 2, where same output buffer is given to peripheral as current and previous. There is no documentation for this core, so register layout and fixed values were taken from BSP driver. I'm not sure if maximum size of the image unit is capable to process is governed by size of "flag" buffers, frequency or it really is some HW limitation. Currently driver can process full HD image in ~15ms (7.5ms for each capture buffer), which allows to process 1920x1080@60i video smoothly in real time. Acked-by: Maxime Ripard Signed-off-by: Jernej Skrabec [hverkuil-cisco@xs4all.nl: add static to deinterlace_ioctl_ops] Signed-off-by: Hans Verkuil Signed-off-by: Mauro Carvalho Chehab

media: sun4i: Make sun4i_csi_formats static

2019-08-30T17:44:17Z

The sun4i_csi_formats array is only used in sun4i_v4l2.c, so it doesn't make any sense to have it !static. [Sakari Ailus: const static -> static const] Reported-by: Hans Verkuil Signed-off-by: Maxime Ripard Signed-off-by: Sakari Ailus Signed-off-by: Mauro Carvalho Chehab

media: sunxi: Add A10 CSI driver

2019-08-23T10:31:35Z

The older CSI drivers have camera capture interface different from the one in the newer ones. This IP is pretty simple. Some variants (one controller out of two instances on some SoCs) have an ISP embedded, but there's no code that make use of it, so we ignored that part for now. [Sakari Ailus: Wrapped a few long lines, set mbus code using a macro.] Signed-off-by: Maxime Ripard Signed-off-by: Sakari Ailus Signed-off-by: Mauro Carvalho Chehab

media: sunxi: Refactor the Makefile and Kconfig

2019-08-23T10:29:05Z

The Makefile and Kconfig for the sun6i CSI driver are included in the main Makefile / KConfig file. Since we're going to add a new CSI driver for an older chip, and the Cedrus driver eventually, it makes more sense to put those in our directory. Signed-off-by: Maxime Ripard Signed-off-by: Sakari Ailus Signed-off-by: Mauro Carvalho Chehab

media: Remove dev_err() usage after platform_get_irq()

2019-08-07T20:08:33Z

We don't need dev_err() messages when platform_get_irq() fails now that platform_get_irq() prints an error message itself when something goes wrong. Let's remove these prints with a simple semantic patch. // @@ expression ret; struct platform_device *E; @@ ret = ( platform_get_irq(E, ...) | platform_get_irq_byname(E, ...) ); if ( \( ret < 0 \| ret <= 0 \) ) { ( -if (ret != -EPROBE_DEFER) -{ ... -dev_err(...); -... } | ... -dev_err(...); ) ... } // While we're here, remove braces on if statements that only have one statement (manually). Cc: Greg Kroah-Hartman Signed-off-by: Stephen Boyd Signed-off-by: Hans Verkuil Signed-off-by: Mauro Carvalho Chehab

media: sun6i: Support A83T variant

2019-05-29T15:27:55Z

The A83T SoC has a camera sensor interface (known as CSI in Allwinner lingo), which is similar to the one found on the A64 and H3. The only difference seems to be that support of MIPI CSI through a connected MIPI CSI-2 bridge. Add support for this variant. Signed-off-by: Chen-Yu Tsai Acked-by: Maxime Ripard Signed-off-by: Sakari Ailus Signed-off-by: Mauro Carvalho Chehab

treewide: Add SPDX license identifier - Makefile/Kconfig

2019-05-21T08:50:46Z

Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner Signed-off-by: Greg Kroah-Hartman