kernel.git/drivers/iio/pressure, branch linux-4.13.y

IIO: BME280: Updates to Humidity readings need ctrl_reg write!

2017-10-12T09:56:11Z

commit 4b1f0c31f96c45e8521dd84aae50f2aa4aecfb7b upstream. The ctrl_reg register needs to be written after any write to the humidity registers. The value written to the ctrl_reg register does not necessarily need to change, but a write operation must occur. The regmap_update_bits functions will not write to a register if the register value matches the value to be written. This saves unnecessary bus operations. The change in this patch forces a bus write during the chip_config operation by switching to regmap_write_bits. This will fix issues where the Humidity Sensor Oversampling bits are not updated after initialization. Signed-off-by: Colin Parker Acked-by: Andreas Klinger Signed-off-by: Jonathan Cameron Signed-off-by: Greg Kroah-Hartman

iio: bmp280: properly initialize device for humidity reading

2017-07-30T13:41:12Z

If the device is not initialized at least once it happens that the humidity reading is skipped, which means the special value 0x8000 is delivered. For omitting this case the oversampling of the humidity must be set before the oversampling of the temperature und pressure is set as written in the datasheet of the BME280. Furthermore proper error detection is added in case a skipped value is read from the device. This is done also for pressure and temperature reading. Especially it don't make sense to compensate this value and treat it as regular value. Signed-off-by: Andreas Klinger Signed-off-by: Jonathan Cameron

Merge tag 'iio-fixes-for-4.13a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus

2017-07-24T03:54:31Z

Jonathan writes: First set of IIO fixes for the 4.13 cycle. * ad2s1210 - Fix negative angular velocity reads (identified by a gcc 7 warning) * aspeed-adc - Wait for initialization sequence to finish before enabling channels. Without it no channels work. * axp288 - Revert a patch that dropped some bogus register mods. No one is entirely sure why but it breaks charging on some devices. - Fix GPADC pin read returning 0. Turns out a small sleep is needed. * bmc150 - Make sure device is restored to normal state after suspend / resume cycle. Otherwise, simple sysfs reads are broken. * tsl2563 - fix wrong event code. * st-accel - add spi 3-wire support. Needed to fix the lsm303agr accelerometer which only had 3 wires in all cases. Side effect is to enable optional 3-wire support for other devices. * st-pressure - disable multiread by default for LPS22HB (only effects SPI) * sun4i-gpadc-iio - fix unbalanced irq enable / disable * vf610 - Fix VALT slection for REFSEL bits - ensures we are using the right reference pins.

iio: pressure: st_pressure_core: disable multiread by default for LPS22HB

2017-06-24T19:46:25Z

Set multiread variable to false for LPS22HB pressure sensor since it is already enabled in CTRL_REG2. Previous configuration does not cause any issue in I2C communication since SUB Msb has no meaning whereas it breaks register address in SPI communication Fixes: e039e2f5b4da (iio:st_pressure:initial lps22hb sensor support) Signed-off-by: Lorenzo Bianconi Cc: Signed-off-by: Jonathan Cameron

iio: pressure: zpa2326: report interrupted case as failure

2017-05-14T14:28:14Z

If the timeout-case prints a warning message then probably the interrupted case should also. Further, wait_for_completion_interruptible_timeout() returns long not int. Fixes: commit 03b262f2bbf4 ("iio:pressure: initial zpa2326 barometer support") Signed-off-by: Nicholas Mc Guire Signed-off-by: Jonathan Cameron

iio: st_pressure: st_accel: Initialise sensor platform data properly

2017-04-26T05:37:53Z

This patch fixes the sensor platform data initialisation for st_pressure and st_accel device drivers. Without this patch, the driver fails to register the sensors when the user removes and re-loads the driver. 1. Unload the kernel modules for st_pressure $ sudo rmmod st_pressure_i2c $ sudo rmmod st_pressure 2. Re-load the driver $ sudo insmod st_pressure $ sudo insmod st_pressure_i2c Signed-off-by: Jonathan Cameron Acked-by: Linus Walleij

iio: pressure: Fix name of BME280 part in Kconfig

2017-04-23T11:38:47Z

Bosch BME280 is a combined pressure and humidity sensor Signed-off-by: Peter Meerwald-Stadler Signed-off-by: Jonathan Cameron

Merge tag 'iio-fixes-for-4.11e' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

2017-04-18T17:38:38Z

Jonathan writes: Fifth set of IIO fixes for the 4.11 cycle. As these are rather late in the cycle, they may sneak over into 4.12. There is a fix for a regression caused by another fix (hid sensors hardware seems to vary a lot in how various corner cases are handled). * ad7303 - fix channel description. Numeric values were being passed as characters presumably leading to garbage from the userspace interface. * as3935 - the write data macro was wrong so fix it. * bmp280 - incorrect handling of negative values as being unsigned broke humidity calculation. * hid-sensor - Restore the poll and hysteresis values after resume as some hardware doesn't do it. * stm32-trigger - buglet in reading the sampling frequency

IIO: bmp280-core.c: fix error in humidity calculation

2017-04-14T15:54:49Z

While calculating the compensation of the humidity there are negative values interpreted as unsigned because of unsigned variables used. These values as well as the constants need to be casted to signed as indicated by the documentation of the sensor. Signed-off-by: Andreas Klinger Acked-by: Linus Walleij Reviewed-by: Matt Ranostay Cc: Signed-off-by: Jonathan Cameron

Merge 4.11-rc6 into staging-next

2017-04-10T13:21:55Z

We want the staging and iio fixes in here to handle merging easier. Signed-off-by: Greg Kroah-Hartman