kernel.git/drivers/iio/imu, branch linux-4.13.y

iio: imu: adis16480: Fix acceleration scale factor for adis16480

2017-08-20T14:21:47Z

According to the datasheet, the range of the acceleration is [-10 g, + 10 g], so the scale factor should be 10 instead of 5. Signed-off-by: Dragos Bogdan Acked-by: Lars-Peter Clausen Cc: Signed-off-by: Jonathan Cameron

Merge tag 'iio-for-4.13b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

2017-06-26T05:09:23Z

Jonathan writes: Second set of IIO new device support, features and cleanups for the 4.13 cycle. A few reverts here. One was a general failure to notice a device was already supported by another driver. The second is due to a review comment pointing out that the original patch was a bad idea and would break existing systems. Reverts * bma180 - Revert addition of support for the BMA250E it is already supported by the bmc150-accel and better supported at that. Oops. * hi8435 - The fix for cleanup of the reset gpio stuff isn't a good way to go. It breaks systems where an inverting level convertor is used. The right fix is to make the original devicetree correct - even if it involves patching the devicetree in kernel. New Device Support * stm32-adc - STM32H7 support and bindings. Features * core - add a hardware triggered operating mode for systems in which the actual trigger is never seen by the kernel. This is typically only used when a device 'can' use other triggers, but if a particular magic one is enabled the interrupt is effectively handled in hardware and we never see it. * st-lsm6dsx - support active low interrupts. * stm32-adc - Make the core adc clock optional as not all hardware supported requires it. - Make the bus clock optional in the per instance driver as it may be shared by all instances of the ADC and is handled by the core. - Rework to have a data structure representing the device type specific elements. * stm32-trigger (and counter) - Use the INDIO_HARDWARE_TRIGGERED_MODE where appropriate. - Add an attribute to configure device modes for quadrature counting etc. Clean ups and minor fixes * IIO core. - use __sysfs_match_string() helper rather than open coding the same. * ad7791 - use sysfs_match_string() helper rather than open coding the same. * aspeed-adc - handle return value of clk_prepare_enable * cpcap - Fix default register values and ensure the battery thermistor is enabled correctly. - Fix the reported die temperature where we can - docs are lacking. - Remove the hung interrupt quirk as no longer happens due to fix in the mfd driver. * hi8435 - Remove &s from hi8435_info definition as unneeded and inconsistent. * hid-sensor-trgger - Add kconfig depends on IIO_BUFFER (fixes patch in previous series) * ina2xx - Make the use of iio_info_mask* elements consistent for all channels. This doesn't have any visible effect, but acts as clear documentation of which channels various resulting attributes apply to. * lpc32xx - handle the return value of clk_prepare_enable. * meson-saradc - NULL instead of 0 for pointer. * mma9551 - use NULL for GPIO connection ID to aid implementation fo ACPI support. Here the connection ID doesn't actually tell us anything and it is much easier to deal with the driver if it's not there. * mpu6050 - Fix lock issues through use of a local mux. - Replace sprintf with scnprintf as appropriate. - Check whoami against all known values. This allows for a small number of boards where we are really fishing for the part not being present at all. It is unfortunately common to have undescribed changes to use newer chips. We paper over this but just emitting a warning for those cases as long as we know about. * mxs-lradc - Fix some non static warnings. * rcar-adc - Part of making the naming for this part consistent across the kernel. * st_accel - drop some spi_device_id entries for variants with no SPI support * st_magn - drop some spi_device_id entries for variants with no SPI support. * sx9500 - Use devm_gpiod_get instead of indexed value with an index of 0 on all occasions. * twl4030 - Drop unused twl4030_get_madc_conversion as callers removed now throughout kernel. - Unexport twl4030_madc_conversion() as no used only within this driver. - Drop twl4030_madc_user_params as not used now. - Drop twl4030_madc_request.func_cb as not used now. - Fold the twl4030-madc.h header into the driver as no longer used anywhere else in the kernel. * xilinx - Handle the return value of clk_prepare_enable

Merge 4.12-rc6 into staging-next

2017-06-20T02:17:45Z

We want the staging fixes in here as well. Signed-off-by: Greg Kroah-Hartman

iio: imu: inv_mpu6050: test whoami first and against all known values

2017-06-13T20:18:17Z

SPI bus is never generating error during transfer, so to check if a chip is correctly connected on a SPI bus we enforce whoami check to be correct. In this way we can assure SPI probe is failing if there is no chip connected. Note that this is really papering over boards that claim the device is there when it isn't. Not a bad thing to cope with, but not necessarily stable material. Fixes: cec0154556f8 ("iio: inv_mpu6050: Check WHO_AM_I register on probe") Signed-off-by: Jean-Baptiste Maneyrol Signed-off-by: Jonathan Cameron

iio: imu: inv_mpu6050: replace sprintf with scnprintf

2017-06-11T14:07:38Z

Signed-off-by: Jean-Baptiste Maneyrol Signed-off-by: Jonathan Cameron

iio: imu: inv_mpu6050: fix lock issues by using our own mutex

2017-06-11T14:07:37Z

There are several locks issues when using buffer and direct polling data at the same time. Use our own mutex for managing locking and block simultaneous use of buffer and direct polling by using iio_device_{claim/release}_direct_mode. This makes chip_config enable bit obsolete, so delete it. Signed-off-by: Jean-Baptiste Maneyrol Signed-off-by: Jonathan Cameron

iio: imu: st_lsm6dsx: support active-low interrupts

2017-06-11T14:07:36Z

Add support for active low interrupts (IRQF_TRIGGER_LOW and IRQF_TRIGGER_FALLING). Configure the device as active high or low according to the requested irq line. Signed-off-by: Lorenzo Bianconi Signed-off-by: Jonathan Cameron

iio: imu: inv_mpu6050: add accel lpf setting for chip >= MPU6500

2017-06-03T08:40:40Z

Starting from MPU6500, accelerometer dlpf is set in a separate register named ACCEL_CONFIG_2. Add this new register in the map and set it for the corresponding chips. Signed-off-by: Jean-Baptiste Maneyrol Cc: stable@vger.kernel.org Signed-off-by: Jonathan Cameron

iio: imu: st_lsm6dsx: substitute ifdef CONFIG_PM with __maybe_unused macro

2017-05-21T14:07:59Z

Get rid of #ifdef CONFIG_PM by adding __maybe_unused macro to st_lsm6dsx_suspend and st_lsm6dsx_resume function declarations Signed-off-by: Lorenzo Bianconi Signed-off-by: Jonathan Cameron

iio: imu: st_lsm6dsx: add system power management support

2017-04-30T16:55:15Z

Add system sleep power management support to st_lsm6dsx driver. In particular during suspend phase each sensor is disabled and hw fifo is configured in bypass in order to avoid subsequent I/O operations. The patch has been tested on HiKey board device Signed-off-by: Lorenzo Bianconi Signed-off-by: Jonathan Cameron