kernel.git/drivers/gpu/drm/msm/hdmi, branch linux-6.15.y

drm/msm/hdmi: add runtime PM calls to DDC transfer function

2025-06-27T10:13:15Z

[ Upstream commit 531b4e2c206e5f7dead04d9da84dfa693ac57481 ] We must be sure that the HDMI controller is powered on, while performing the DDC transfer. Add corresponding runtime PM calls to msm_hdmi_i2c_xfer(). Reviewed-by: Jessica Zhang Signed-off-by: Dmitry Baryshkov Patchwork: https://patchwork.freedesktop.org/patch/651727/ Link: https://lore.kernel.org/r/20250505-fd-hdmi-hpd-v5-8-48541f76318c@oss.qualcomm.com Signed-off-by: Dmitry Baryshkov Signed-off-by: Sasha Levin

drm/msm/hdmi: use DRM HDMI Audio framework

2025-03-05T02:34:13Z

In order to simplify the driver even further and to remove the boilerplate code, rewrite the audio interface to use the DRM HDMI Audio framework. Audio InfoFames are controlled centrally via the DRM HDMI framework. Correct InfoFrame data is programmed at the atomic_pre_enable() time (if it was set before, drm_atomic_helper_connector_hdmi_update_infoframes() takes care of writing all InfoFrames, including the Audio one.) or during msm_hdmi_bridge_audio_prepare() when the new stream is started. All audio data frame management is deferred to msm_hdmi_bridge_audio_prepare() and msm_hdmi_bridge_audio_shutdown(). Reviewed-by: Maxime Ripard Reviewed-by: Abhinav Kumar Signed-off-by: Dmitry Baryshkov Patchwork: https://patchwork.freedesktop.org/patch/639663/ Link: https://lore.kernel.org/r/20250226-bridge-hdmi-connector-v8-7-340af24b35cc@linaro.org

drm/msm/hdmi: also send the SPD and HDMI Vendor Specific InfoFrames

2025-03-05T02:34:13Z

Extend the driver to send SPD and HDMI Vendor Specific InfoFrames. While the HDMI block has special block to send HVS InfoFrame, use GENERIC0 block instead. VENSPEC_INFO registers pack frame data in a way that requires manual repacking in the driver, while GENERIC0 doesn't have such format requirements. The msm-4.4 kernel uses GENERIC0 to send HDR InfoFrame which we do not at this point anyway. Acked-by: Maxime Ripard Reviewed-by: Abhinav Kumar Signed-off-by: Dmitry Baryshkov Patchwork: https://patchwork.freedesktop.org/patch/639661/ Link: https://lore.kernel.org/r/20250226-bridge-hdmi-connector-v8-6-340af24b35cc@linaro.org

drm/msm/hdmi: get rid of hdmi_mode

2025-03-05T02:34:13Z

Use connector->display_info.is_hdmi instead of manually using drm_detect_hdmi_monitor(). Acked-by: Maxime Ripard Reviewed-by: Abhinav Kumar Signed-off-by: Dmitry Baryshkov Patchwork: https://patchwork.freedesktop.org/patch/639657/ Link: https://lore.kernel.org/r/20250226-bridge-hdmi-connector-v8-4-340af24b35cc@linaro.org

drm/msm/hdmi: make use of the drm_connector_hdmi framework

2025-03-05T02:34:13Z

Setup the HDMI connector on the MSM HDMI outputs. Make use of atomic_check hook and of the provided Infoframe infrastructure. Acked-by: Maxime Ripard Reviewed-by: Abhinav Kumar Signed-off-by: Dmitry Baryshkov Patchwork: https://patchwork.freedesktop.org/patch/639656/ Link: https://lore.kernel.org/r/20250226-bridge-hdmi-connector-v8-3-340af24b35cc@linaro.org

drm/msm/hdmi: program HDMI timings during atomic_pre_enable

2025-03-05T02:34:12Z

The mode_set callback is deprecated, it doesn't get the drm_bridge_state, just mode-related argumetns. Also Abhinav pointed out that HDMI timings should be programmed before setting up HDMI PHY and PLL. Rework the code to program HDMI timings at the start of atomic_pre_enable(). Reviewed-by: Maxime Ripard Reviewed-by: Abhinav Kumar Signed-off-by: Dmitry Baryshkov Patchwork: https://patchwork.freedesktop.org/patch/639652/ Link: https://lore.kernel.org/r/20250226-bridge-hdmi-connector-v8-2-340af24b35cc@linaro.org

drm/msm/hdmi: switch to atomic bridge callbacks

2025-03-05T02:34:12Z

Change MSM HDMI bridge to use atomic_* callbacks in preparation to enablign the HDMI connector support. Acked-by: Maxime Ripard Reviewed-by: Abhinav Kumar Signed-off-by: Dmitry Baryshkov Patchwork: https://patchwork.freedesktop.org/patch/639653/ Link: https://lore.kernel.org/r/20250226-bridge-hdmi-connector-v8-1-340af24b35cc@linaro.org

Merge tag 'drm-msm-next-2025-01-07' of gitlab.freedesktop.org:drm/msm into drm-next

2025-01-13T01:14:07Z

Updates for v6.14 MDSS: - properly described UBWC registers - added SM6150 (aka QCS615) support MDP4: - several small fixes DPU: - added SM6150 (aka QCS615) support - enabled wide planes if virtual planes are enabled (by using two SSPPs for a single plane) - fixed modes filtering for platforms w/o 3DMux - fixed DSPP DSPP_2 / _3 links on several platforms - corrected DSPP definitions on SDM670 - added CWB hardware blocks support - added VBIF to DPU snapshots - dropped struct dpu_rm_requirements DP: - reworked DP audio support DSI: - added SM6150 (aka QCS615) support GPU: - Print GMU core fw version - GMU bandwidth voting for a740 and a750 - Expose uche trap base via uapi - UAPI error reporting Signed-off-by: Dave Airlie From: Rob Clark Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGsutUu4ff6OpXNXxqf1xaV0rV6oV23VXNRiF0_OEfe72Q@mail.gmail.com

drm/msm/hdmi: simplify code in pll_get_integloop_gain

2024-12-03T02:59:01Z

In pll_get_integloop_gain(), digclk_divsel=1 or 2, base=63 or 196ULL, so the base may be 63, 126, 196, 392. The condition base <= 2046 always true. Fixes: caedbf17c48d ("drm/msm: add msm8998 hdmi phy/pll support") Signed-off-by: Rex Nie Reviewed-by: Dmitry Baryshkov Reviewed-by: Abhinav Kumar Patchwork: https://patchwork.freedesktop.org/patch/624153/ Link: https://lore.kernel.org/r/20241112074101.2206-1-rex.nie@jaguarmicro.com Signed-off-by: Abhinav Kumar

Get rid of 'remove_new' relic from platform driver struct

2024-12-01T23:12:43Z

The continual trickle of small conversion patches is grating on me, and is really not helping. Just get rid of the 'remove_new' member function, which is just an alias for the plain 'remove', and had a comment to that effect: /* * .remove_new() is a relic from a prototype conversion of .remove(). * New drivers are supposed to implement .remove(). Once all drivers are * converted to not use .remove_new any more, it will be dropped. */ This was just a tree-wide 'sed' script that replaced '.remove_new' with '.remove', with some care taken to turn a subsequent tab into two tabs to make things line up. I did do some minimal manual whitespace adjustment for places that used spaces to line things up. Then I just removed the old (sic) .remove_new member function, and this is the end result. No more unnecessary conversion noise. Signed-off-by: Linus Torvalds