kernel.git/drivers/gpu/drm/msm/dsi/phy, branch linux-6.1.y

drm/msm/dsi/phy_7nm: Fix missing initial VCO rate

2025-12-06T21:12:21Z

[ Upstream commit 5ddcb0cb9d10e6e70a68e0cb8f0b8e3a7eb8ccaf ] Driver unconditionally saves current state on first init in dsi_pll_7nm_init(), but does not save the VCO rate, only some of the divider registers. The state is then restored during probe/enable via msm_dsi_phy_enable() -> msm_dsi_phy_pll_restore_state() -> dsi_7nm_pll_restore_state(). Restoring calls dsi_pll_7nm_vco_set_rate() with pll_7nm->vco_current_rate=0, which basically overwrites existing rate of VCO and messes with clock hierarchy, by setting frequency to 0 to clock tree. This makes anyway little sense - VCO rate was not saved, so should not be restored. If PLL was not configured configure it to minimum rate to avoid glitches and configuring entire in clock hierarchy to 0 Hz. Reviewed-by: Dmitry Baryshkov Signed-off-by: Krzysztof Kozlowski Patchwork: https://patchwork.freedesktop.org/patch/657827/ Link: https://lore.kernel.org/r/20250610-b4-sm8750-display-v6-9-ee633e3ddbff@linaro.org Signed-off-by: Dmitry Baryshkov Signed-off-by: Sasha Levin

drm/msm/dsi/phy: Toggle back buffer resync after preparing PLL

2025-12-06T21:12:21Z

[ Upstream commit b63f008f395ca5f6bc89123db97440bdc19981c4 ] According to Hardware Programming Guide for DSI PHY, the retime buffer resync should be done after PLL clock users (byte_clk and intf_byte_clk) are enabled. Downstream also does it as part of configuring the PLL. Driver was only turning off the resync FIFO buffer, but never bringing it on again. Reviewed-by: Dmitry Baryshkov Signed-off-by: Krzysztof Kozlowski Patchwork: https://patchwork.freedesktop.org/patch/657823/ Link: https://lore.kernel.org/r/20250610-b4-sm8750-display-v6-6-ee633e3ddbff@linaro.org Signed-off-by: Dmitry Baryshkov Signed-off-by: Sasha Levin

drm/msm/dsi/dsi_phy_10nm: Fix missing initial VCO rate

2025-06-27T10:07:38Z

[ Upstream commit 8a48e35becb214743214f5504e726c3ec131cd6d ] Driver unconditionally saves current state on first init in dsi_pll_10nm_init(), but does not save the VCO rate, only some of the divider registers. The state is then restored during probe/enable via msm_dsi_phy_enable() -> msm_dsi_phy_pll_restore_state() -> dsi_10nm_pll_restore_state(). Restoring calls dsi_pll_10nm_vco_set_rate() with pll_10nm->vco_current_rate=0, which basically overwrites existing rate of VCO and messes with clock hierarchy, by setting frequency to 0 to clock tree. This makes anyway little sense - VCO rate was not saved, so should not be restored. If PLL was not configured configure it to minimum rate to avoid glitches and configuring entire in clock hierarchy to 0 Hz. Suggested-by: Dmitry Baryshkov Link: https://lore.kernel.org/r/sz4kbwy5nwsebgf64ia7uq4ee7wbsa5uy3xmlqwcstsbntzcov@ew3dcyjdzmi2/ Signed-off-by: Krzysztof Kozlowski Fixes: a4ccc37693a2 ("drm/msm/dsi_pll_10nm: restore VCO rate during Reviewed-by: Dmitry Baryshkov Patchwork: https://patchwork.freedesktop.org/patch/654796/ Link: https://lore.kernel.org/r/20250520111325.92352-2-krzysztof.kozlowski@linaro.org Signed-off-by: Dmitry Baryshkov Signed-off-by: Sasha Levin

drm/msm/dsi: Enable runtime PM

2024-02-05T20:13:02Z

commit 6ab502bc1cf3147ea1d8540d04b83a7a4cb6d1f1 upstream. Some devices power the DSI PHY/PLL through a power rail that we model as a GENPD. Enable runtime PM to make it suspendable. Signed-off-by: Konrad Dybcio Reviewed-by: Dmitry Baryshkov Patchwork: https://patchwork.freedesktop.org/patch/543352/ Link: https://lore.kernel.org/r/20230620-topic-dsiphy_rpm-v2-2-a11a751f34f0@linaro.org Signed-off-by: Dmitry Baryshkov Signed-off-by: Amit Pundir Signed-off-by: Greg Kroah-Hartman

drm/msm/dsi: Use pm_runtime_resume_and_get to prevent refcnt leaks

2024-01-25T23:27:33Z

[ Upstream commit 3d07a411b4faaf2b498760ccf12888f8de529de0 ] This helper has been introduced to avoid programmer errors (missing _put calls leading to dangling refcnt) when using pm_runtime_get, use it. While at it, start checking the return value. Signed-off-by: Konrad Dybcio Reviewed-by: Dmitry Baryshkov Fixes: 5c8290284402 ("drm/msm/dsi: Split PHY drivers to separate files") Patchwork: https://patchwork.freedesktop.org/patch/543350/ Link: https://lore.kernel.org/r/20230620-topic-dsiphy_rpm-v2-1-a11a751f34f0@linaro.org Signed-off-by: Dmitry Baryshkov Signed-off-by: Sasha Levin

drm/msm/dsi: don't allow enabling 14nm VCO with unprogrammed rate

2023-07-19T14:21:20Z

[ Upstream commit 1e0a97f84d73ea1182740f62069690c7f3271abb ] If the dispcc uses CLK_OPS_PARENT_ENABLE (e.g. on QCM2290), CCF can try enabling VCO before the rate has been programmed. This can cause clock lockups and/or other boot issues. Program the VCO to the minimal PLL rate if the read rate is 0 Hz. Cc: Konrad Dybcio Signed-off-by: Dmitry Baryshkov Reported-by: Vladimir Zapolskiy Reported-by: Konrad Dybcio Reviewed-by: Konrad Dybcio Fixes: f079f6d999cb ("drm/msm/dsi: Add PHY/PLL for 8x96") Patchwork: https://patchwork.freedesktop.org/patch/534813/ Link: https://lore.kernel.org/r/20230501011257.3460103-1-dmitry.baryshkov@linaro.org Signed-off-by: Dmitry Baryshkov Signed-off-by: Sasha Levin

drm/msm/dsi: Improve dsi_phy_driver_probe() probe error handling

2022-09-18T16:38:06Z

The dsi_phy_driver_probe() function has a "goto fail" for no reason. Change it to just always return directly when it sees an error. Make this simpler by leveraging dev_err_probe() which is designed to make code like this shorter / simpler. NOTE: as part of this, we now pass through error codes directly from msm_ioremap_size() rather than translating to -ENOMEM. This changed mostly because it's much more convenient when using dev_err_probe() and also it's usually encouraged not to hide error codes like the old code was doing unless there is a good reason. I can't see any reason why we'd need to return -ENOMEM instead of -EINVAL from the probe function. Signed-off-by: Douglas Anderson Reviewed-by: Dmitry Baryshkov Reviewed-by: Abhinav Kumar Patchwork: https://patchwork.freedesktop.org/patch/496324/ Link: https://lore.kernel.org/r/20220804073608.v4.6.I969118a35934a0e5007fe4f80e3e28e9c0b7602a@changeid Signed-off-by: Dmitry Baryshkov Signed-off-by: Rob Clark

drm/msm/dsi: Take advantage of devm_regulator_bulk_get_const()

2022-09-18T16:38:06Z

As of the commit 1de452a0edda ("regulator: core: Allow drivers to define their init data as const") we no longer need to do copying of regulator bulk data from initdata to something dynamic. Let's take advantage of that. In addition to saving some code, this also moves us to using ARRAY_SIZE() to specify how many regulators we have which is less error prone. This gets rid of some layers of wrappers which makes it obvious that we can get rid of an extra error print. devm_regulator_bulk_get_const() prints errors for you so you don't need an extra layer of printing. In all cases here I have preserved the old settings without any investigation about whether the loads being set are sensible. In the cases of some of the PHYs if several PHYs in the same file used exactly the same settings I had them point to the same data structure. NOTE: Though I haven't done the math, this is likely an overall savings in terms of "static const" data. We previously always allocated space for 8 supplies. Each of these supplies took up 36 bytes of data (32 for name, 4 for an int). Signed-off-by: Douglas Anderson Reviewed-by: Dmitry Baryshkov Reviewed-by: Abhinav Kumar Patchwork: https://patchwork.freedesktop.org/patch/496325/ Link: https://lore.kernel.org/r/20220804073608.v4.5.I55a9e65cb1c22221316629e98768ff473f47a067@changeid Signed-off-by: Dmitry Baryshkov Signed-off-by: Rob Clark

drm/msm/dsi: Use the new regulator bulk feature to specify the load

2022-09-18T16:38:05Z

As of commit 6eabfc018e8d ("regulator: core: Allow specifying an initial load w/ the bulk API") we can now specify the initial load in the bulk data rather than having to manually call regulator_set_load() on each regulator. Let's use it. Signed-off-by: Douglas Anderson Reviewed-by: Dmitry Baryshkov Reviewed-by: Abhinav Kumar Patchwork: https://patchwork.freedesktop.org/patch/496319/ Link: https://lore.kernel.org/r/20220804073608.v4.4.I7b3c72949883846badb073cfeae985c55239da1d@changeid Signed-off-by: Dmitry Baryshkov Signed-off-by: Rob Clark

drm/msm/dsi: Don't set a load before disabling a regulator

2022-09-18T16:38:05Z

As of commit 5451781dadf8 ("regulator: core: Only count load for enabled consumers"), a load isn't counted for a disabled regulator. That means all the code in the DSI driver to specify and set loads before disabling a regulator is not actually doing anything useful. Let's remove it. It should be noted that all of the loads set that were being specified were pointless noise anyway. The only use for this number is to pick between low power and high power modes of regulators. Regulators appear to do this changeover at loads on the order of 10000 uA. You would need a lot of clients of the same rail for that 100 uA number to count for anything. Note that now that we get rid of the setting of the load at disable time, we can just set the load once when we first get the regulator and then forget it. It should also be noted that the regulator functions regulator_bulk_enable() and regulator_set_load() already print error messages when they encounter problems so while moving things around we get rid of some extra error prints. Signed-off-by: Douglas Anderson Reviewed-by: Dmitry Baryshkov Reviewed-by: Abhinav Kumar Patchwork: https://patchwork.freedesktop.org/patch/496320/ Link: https://lore.kernel.org/r/20220804073608.v4.3.If1f94fbbdb7c1d0fb3961de61483a851ad1971a7@changeid Signed-off-by: Dmitry Baryshkov Signed-off-by: Rob Clark