kernel.git/drivers/gpu/drm/msm/dp, branch linux-5.13.y

drm/msm/dp: do not end dp link training until video is ready

2021-09-18T11:42:11Z

[ Upstream commit 2e0adc765d884cc080baa501e250bfad97035b09 ] Initialize both pre-emphasis and voltage swing level to 0 before start link training and do not end link training until video is ready to reduce the period between end of link training and video start to meet Link Layer CTS requirement. Some dongle main link symbol may become unlocked again if host did not end link training soon enough after completion of link training 2. Host have to re train main link if loss of symbol locked detected before end link training so that the coming video stream can be transmitted to sink properly. This fixes Link Layer CTS cases 4.3.2.1, 4.3.2.2, 4.3.2.3 and 4.3.2.4. Changes in v3: -- merge retrain link if loss of symbol locked happen into this patch -- replace dp_ctrl_loss_symbol_lock() with dp_ctrl_channel_eq_ok() Signed-off-by: Kuogee Hsieh Reviewed-by: Stephen Boyd Link: https://lore.kernel.org/r/1628196295-7382-7-git-send-email-khsieh@codeaurora.org Signed-off-by: Rob Clark Signed-off-by: Sasha Levin

drm/msm/dp: return correct edid checksum after corrupted edid checksum read

2021-09-18T11:42:11Z

[ Upstream commit 7948fe12d47a946fb8025a0534c900e3dd4b5839 ] Response with correct edid checksum saved at connector after corrupted edid checksum read. This fixes Link Layer CTS cases 4.2.2.3, 4.2.2.6. Signed-off-by: Kuogee Hsieh Reviewed-by: Stephen Boyd Link: https://lore.kernel.org/r/1628196295-7382-6-git-send-email-khsieh@codeaurora.org Signed-off-by: Rob Clark Signed-off-by: Sasha Levin

drm/msm/dp: reduce link rate if failed at link training 1

2021-09-18T11:42:10Z

[ Upstream commit 4b85d405cfe938ae7ad61656484ae88dee289e3b ] Reduce link rate and re start link training if link training 1 failed due to loss of clock recovery done to fix Link Layer CTS case 4.3.1.7. Also only update voltage and pre-emphasis swing level after link training started to fix Link Layer CTS case 4.3.1.6. Changes in V2: -- replaced cr_status with link_status[DP_LINK_STATUS_SIZE] -- replaced dp_ctrl_any_lane_cr_done() with dp_ctrl_colco_recovery_any_ok() -- replaced dp_ctrl_any_ane_cr_lose() with !drm_dp_clock_recovery_ok() Changes in V3: -- return failed if lane_count <= 1 Signed-off-by: Kuogee Hsieh Reviewed-by: Stephen Boyd Link: https://lore.kernel.org/r/1628196295-7382-3-git-send-email-khsieh@codeaurora.org [remove unused cr_status variable] Signed-off-by: Rob Clark Signed-off-by: Sasha Levin

drm/msm/dp: replug event is converted into an unplug followed by an plug events

2021-09-15T08:00:46Z

[ Upstream commit 7e10bf427850f2d7133fd091999abd5fc1755cdb ] Remove special handling of replug interrupt and instead treat replug event as a sequential unplug followed by a plugin event. This is needed to meet the requirements of DP Link Layer CTS test case 4.2.1.3. Changes in V2: -- add fixes statement Changes in V3: -- delete EV_HPD_REPLUG_INT Fixes: f21c8a276c2d ("drm/msm/dp: handle irq_hpd with sink_count = 0 correctly") Signed-off-by: Kuogee Hsieh Reviewed-by: Stephen Boyd Link: https://lore.kernel.org/r/1628196295-7382-5-git-send-email-khsieh@codeaurora.org Signed-off-by: Rob Clark Signed-off-by: Sasha Levin

drm/msm/dp: update is_connected status base on sink count at dp_pm_resume()

2021-09-15T08:00:45Z

[ Upstream commit e8a767e04dbc7b201cb17ab99dca723a3488b6d4 ] Currently at dp_pm_resume() is_connected state is decided base on hpd connection status only. This will put is_connected in wrongly "true" state at the scenario that dongle attached to DUT but without hmdi cable connecting to it. Fix this problem by adding read sink count from dongle and decided is_connected state base on both sink count and hpd connection status. Changes in v2: -- remove dp_get_sink_count() cand call drm_dp_read_sink_count() Changes in v3: -- delete status local variable from dp_pm_resume() Changes in v4: -- delete un necessary comment at dp_pm_resume() Fixes: d9aa6571b28ba ("drm/msm/dp: check sink_count before update is_connected status") Signed-off-by: Kuogee Hsieh Link: https://lore.kernel.org/r/1628092261-32346-1-git-send-email-khsieh@codeaurora.org Tested-by: Stephen Boyd Reviewed-by: Stephen Boyd Signed-off-by: Dmitry Baryshkov Signed-off-by: Rob Clark Signed-off-by: Sasha Levin

drm/msm/dp: Initialize the INTF_CONFIG register

2021-08-04T10:47:54Z

[ Upstream commit f9a39932fa54b6421e751ada7a285da809146421 ] Some bootloaders set the widebus enable bit in the INTF_CONFIG register, but configuration of widebus isn't yet supported ensure that the register has a known value, with widebus disabled. Fixes: c943b4948b58 ("drm/msm/dp: add displayPort driver support") Signed-off-by: Bjorn Andersson Reviewed-by: Stephen Boyd Link: https://lore.kernel.org/r/20210722024434.3313167-1-bjorn.andersson@linaro.org Signed-off-by: Rob Clark Signed-off-by: Sasha Levin

drm/msm/dp: use dp_ctrl_off_link_stream during PHY compliance test run

2021-08-04T10:47:54Z

[ Upstream commit 7591c532b818ef4b8e3e635d842547c08b3a32b4 ] DP cable should always connect to DPU during the entire PHY compliance testing run. Since DP PHY compliance test is executed at irq_hpd event context, dp_ctrl_off_link_stream() should be used instead of dp_ctrl_off(). dp_ctrl_off() is used for unplug event which is triggered when DP cable is dis connected. Changes in V2: -- add fixes statement Fixes: f21c8a276c2d ("drm/msm/dp: handle irq_hpd with sink_count = 0 correctly") Signed-off-by: Kuogee Hsieh Reviewed-by: Stephen Boyd Link: https://lore.kernel.org/r/1626191647-13901-2-git-send-email-khsieh@codeaurora.org Signed-off-by: Rob Clark Signed-off-by: Sasha Levin

drm/msm/dp: handle irq_hpd with sink_count = 0 correctly

2021-07-14T15:07:16Z

[ Upstream commit f21c8a276c2daddddf58d483b49b01d0603f0316 ] irq_hpd interrupt should be handled after dongle plugged in and before dongle unplugged. Hence irq_hpd interrupt is enabled at the end of the plugin handle and disabled at the beginning of unplugged handle. Current irq_hpd with sink_count = 0 is wrongly handled same as the dongle unplugged which tears down the mainlink and disables the phy. This patch fixes this problem by only tearing down the mainlink but keeping phy enabled at irq_hpd with sink_count = 0 handle so that next irq_hpd with sink_count =1 can be handled by setup mainlink only. This patch also set dongle into D3 (power off) state at end of handling irq_hpd with sink_count = 0. Changes in v2: -- add ctrl->phy_Power_count Changes in v3: -- del ctrl->phy_Power_count -- add phy_power_off to dp_ctrl_off_link_stream() Changes in v4: -- return immediately if clock disable failed at dp_ctrl_off_link_stream() Changes in v5: -- set dongle to D3 (power off) state at dp_ctrl_off_link_stream() Changes in v6: -- add Fixes tag Fixes: ea9f337ce81e ("drm/msm/dp: reset dp controller only at boot up and pm_resume") Signed-off-by: Kuogee Hsieh Tested-by: Stephen Boyd Reviewed-by: Stephen Boyd Link: https://lore.kernel.org/r/1621635930-30161-1-git-send-email-khsieh@codeaurora.org Signed-off-by: Rob Clark Signed-off-by: Sasha Levin

drm/msm/dp: initialize audio_comp when audio starts

2021-05-06T23:26:57Z

Initialize audio_comp when audio starts and wait for audio_comp at dp_display_disable(). This will take care of both dongle unplugged and display off (suspend) cases. Changes in v2: -- add dp_display_signal_audio_start() Changes in v3: -- restore dp_display_handle_plugged_change() at dp_hpd_unplug_handle(). Changes in v4: -- none Signed-off-by: Kuogee Hsieh Reviewed-by: Stephen Boyd Tested-by: Stephen Boyd Fixes: c703d5789590 ("drm/msm/dp: trigger unplug event in msm_dp_display_disable") Link: https://lore.kernel.org/r/1619048258-8717-3-git-send-email-khsieh@codeaurora.org Signed-off-by: Rob Clark

drm/msm/dp: check sink_count before update is_connected status

2021-05-06T23:26:01Z

Link status is different from display connected status in the case of something like an Apple dongle where the type-c plug can be connected, and therefore the link is connected, but no sink is connected until an HDMI cable is plugged into the dongle. The sink_count of DPCD of dongle will increase to 1 once an HDMI cable is plugged into the dongle so that display connected status will become true. This checking also apply at pm_resume. Changes in v4: -- none Fixes: 94e58e2d06e3 ("drm/msm/dp: reset dp controller only at boot up and pm_resume") Reported-by: Stephen Boyd Reviewed-by: Stephen Boyd Tested-by: Stephen Boyd Signed-off-by: Kuogee Hsieh Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Link: https://lore.kernel.org/r/1619048258-8717-2-git-send-email-khsieh@codeaurora.org Signed-off-by: Rob Clark