kernel.git/drivers/gpu/drm/bridge, branch linux-6.4.y

drm: adv7511: Fix low refresh rate register for ADV7533/5

2023-09-13T07:48:14Z

[ Upstream commit d281eeaa4de2636ff0c8e6ae387bb07b50e5fcbb ] For ADV7533 and ADV7535 low refresh rate is selected using bits [3:2] of 0x4a main register. So depending on ADV model write 0xfb or 0x4a register. Fixes: 2437e7cd88e8 ("drm/bridge: adv7533: Initial support for ADV7533") Reviewed-by: Robert Foss Reviewed-by: Nuno Sa Signed-off-by: Bogdan Togorean Signed-off-by: Alexandru Ardelean Reviewed-by: Frieder Schrempf Signed-off-by: Robert Foss Link: https://patchwork.freedesktop.org/patch/msgid/20230719060143.63649-1-alex@shruggie.ro Signed-off-by: Sasha Levin

drm/bridge: anx7625: Use common macros for HDCP capabilities

2023-09-13T07:48:13Z

[ Upstream commit 41639b3a8b0f1f194dfe0577d99db70613f78626 ] The DRM DP code has macros for the DP HDCP capabilities. Use them in the anx7625 driver instead of raw numbers. Fixes: cd1637c7e480 ("drm/bridge: anx7625: add HDCP support") Suggested-by: Nícolas F. R. A. Prado Signed-off-by: Chen-Yu Tsai Reviewed-by: Robert Foss Signed-off-by: Robert Foss Link: https://patchwork.freedesktop.org/patch/msgid/20230710091203.1874317-1-wenst@chromium.org Signed-off-by: Sasha Levin

drm/bridge: anx7625: Use common macros for DP power sequencing commands

2023-09-13T07:48:13Z

[ Upstream commit 2ba776f903cb7157e80b5f314fb0b4faf6ea6958 ] The DRM DP code has macros for the DP power sequencing commands. Use them in the anx7625 driver instead of raw numbers. Fixes: 548b512e144f ("drm/bridge: anx7625: send DPCD command to downstream") Fixes: 27f26359de9b ("drm/bridge: anx7625: Set downstream sink into normal status") Signed-off-by: Chen-Yu Tsai Reviewed-by: Nícolas F. R. A. Prado Signed-off-by: Robert Foss Link: https://patchwork.freedesktop.org/patch/msgid/20230710090929.1873646-1-wenst@chromium.org Signed-off-by: Sasha Levin

drm: bridge: dw-mipi-dsi: Fix enable/disable of DSI controller

2023-09-13T07:48:09Z

[ Upstream commit 05aa61334592adb230749ff465b103ee10e63936 ] Before this patch, booting to Linux VT and doing a simple: echo 2 > /sys/class/graphics/fb0/blank echo 0 > /sys/class/graphics/fb0/blank would result in failures to re-enable the panel. Mode set callback is called only once during boot in this scenario, while calls to enable/disable callbacks are balanced afterwards. The driver doesn't work unless userspace calls modeset before enabling the CRTC/connector. This patch moves enabling of the DSI host from mode_set into pre_enable callback, and removes some old hacks where this bridge driver is directly calling into other bridge driver's callbacks. pre_enable_prev_first flag is set on the panel's bridge so that panel drivers will get their prepare function called between DSI host's pre_enable and enable callbacks, so that they get a chance to perform panel setup while DSI host is already enabled in command mode. Otherwise panel's prepare would be called before DSI host is enabled, and any DSI communication used in prepare callback would fail. With all these changes, the enable/disable sequence is now well balanced, and host's and panel's callbacks are called in proper order documented in the drm_panel API documentation without needing the old hacks. (Mainly that panel->prepare is called when DSI host is ready to allow the panel driver to send DSI commands and vice versa during disable.) Tested on Pinephone Pro. Trace of the callbacks follows. Before: [ 1.253882] dw-mipi-dsi-rockchip ff960000.dsi: mode_set [ 1.290732] panel-himax-hx8394 ff960000.dsi.0: prepare [ 1.475576] dw-mipi-dsi-rockchip ff960000.dsi: enable [ 1.475593] panel-himax-hx8394 ff960000.dsi.0: enable echo 2 > /sys/class/graphics/fb0/blank [ 13.722799] panel-himax-hx8394 ff960000.dsi.0: disable [ 13.774502] dw-mipi-dsi-rockchip ff960000.dsi: post_disable [ 13.774526] panel-himax-hx8394 ff960000.dsi.0: unprepare echo 0 > /sys/class/graphics/fb0/blank [ 17.735796] panel-himax-hx8394 ff960000.dsi.0: prepare [ 17.923522] dw-mipi-dsi-rockchip ff960000.dsi: enable [ 17.923540] panel-himax-hx8394 ff960000.dsi.0: enable [ 17.944330] dw-mipi-dsi-rockchip ff960000.dsi: failed to write command FIFO [ 17.944335] panel-himax-hx8394 ff960000.dsi.0: sending command 0xb9 failed: -110 [ 17.944340] panel-himax-hx8394 ff960000.dsi.0: Panel init sequence failed: -110 echo 2 > /sys/class/graphics/fb0/blank [ 431.148583] panel-himax-hx8394 ff960000.dsi.0: disable [ 431.169259] dw-mipi-dsi-rockchip ff960000.dsi: failed to write command FIFO [ 431.169268] panel-himax-hx8394 ff960000.dsi.0: Failed to enter sleep mode: -110 [ 431.169282] dw-mipi-dsi-rockchip ff960000.dsi: post_disable [ 431.169316] panel-himax-hx8394 ff960000.dsi.0: unprepare [ 431.169357] pclk_mipi_dsi0 already disabled echo 0 > /sys/class/graphics/fb0/blank [ 432.796851] panel-himax-hx8394 ff960000.dsi.0: prepare [ 432.981537] dw-mipi-dsi-rockchip ff960000.dsi: enable [ 432.981568] panel-himax-hx8394 ff960000.dsi.0: enable [ 433.002290] dw-mipi-dsi-rockchip ff960000.dsi: failed to write command FIFO [ 433.002299] panel-himax-hx8394 ff960000.dsi.0: sending command 0xb9 failed: -110 [ 433.002312] panel-himax-hx8394 ff960000.dsi.0: Panel init sequence failed: -110 ----------------------------------------------------------------------- After: [ 1.248372] dw-mipi-dsi-rockchip ff960000.dsi: mode_set [ 1.248704] dw-mipi-dsi-rockchip ff960000.dsi: pre_enable [ 1.285377] panel-himax-hx8394 ff960000.dsi.0: prepare [ 1.468392] dw-mipi-dsi-rockchip ff960000.dsi: enable [ 1.468421] panel-himax-hx8394 ff960000.dsi.0: enable echo 2 > /sys/class/graphics/fb0/blank [ 16.210357] panel-himax-hx8394 ff960000.dsi.0: disable [ 16.261315] dw-mipi-dsi-rockchip ff960000.dsi: post_disable [ 16.261339] panel-himax-hx8394 ff960000.dsi.0: unprepare echo 0 > /sys/class/graphics/fb0/blank [ 19.161453] dw-mipi-dsi-rockchip ff960000.dsi: pre_enable [ 19.197869] panel-himax-hx8394 ff960000.dsi.0: prepare [ 19.382141] dw-mipi-dsi-rockchip ff960000.dsi: enable [ 19.382158] panel-himax-hx8394 ff960000.dsi.0: enable (But depends on functionality intorduced in Linux 6.3, so this patch will not build on older kernels when applied to older stable branches.) Fixes: 46fc51546d44 ("drm/bridge/synopsys: Add MIPI DSI host controller bridge") Signed-off-by: Ondrej Jirman Reviewed-by: Sam Ravnborg Signed-off-by: Robert Foss Link: https://patchwork.freedesktop.org/patch/msgid/20230617224915.1923630-1-megi@xff.cz Signed-off-by: Sasha Levin

drm/bridge: tc358764: Fix debug print parameter order

2023-09-13T07:48:09Z

[ Upstream commit 7f947be02aab5b154427cb5b0fffe858fc387b02 ] The debug print parameters were swapped in the output and they were printed as decimal values, both the hardware address and the value. Update the debug print to print the parameters in correct order, and use hexadecimal print for both address and value. Fixes: f38b7cca6d0e ("drm/bridge: tc358764: Add DSI to LVDS bridge driver") Signed-off-by: Marek Vasut Reviewed-by: Robert Foss Signed-off-by: Robert Foss Link: https://patchwork.freedesktop.org/patch/msgid/20230615152817.359420-1-marex@denx.de Signed-off-by: Sasha Levin

drm/bridge: it6505: Check power state with it6505->powered in IRQ handler

2023-08-16T16:32:26Z

commit e9d699af3f65d62cf195f0e7a039400093ab2af2 upstream. On system resume, the driver might call it6505_poweron directly if the runtime PM hasn't been enabled. In such case, pm_runtime_get_if_in_use will always return 0 because dev->power.runtime_status stays at RPM_SUSPENDED, and the IRQ will never be handled. Use it6505->powered from the driver struct fixes this because it always gets updated when it6505_poweron is called. Fixes: 5eb9a4314053 ("drm/bridge: it6505: Guard bridge power in IRQ handler") Signed-off-by: Pin-yen Lin Reviewed-by: Neil Armstrong Signed-off-by: Neil Armstrong Link: https://patchwork.freedesktop.org/patch/msgid/20230727100131.2338127-1-treapking@chromium.org Signed-off-by: Greg Kroah-Hartman

drm/bridge: ti-sn65dsi86: Fix auxiliary bus lifetime

2023-07-23T11:53:36Z

[ Upstream commit 7aa83fbd712a6f08ffa67890061f26d140c2a84f ] Memory for the "struct device" for any given device isn't supposed to be released until the device's release() is called. This is important because someone might be holding a kobject reference to the "struct device" and might try to access one of its members even after any other cleanup/uninitialization has happened. Code analysis of ti-sn65dsi86 shows that this isn't quite right. When the code was written, it was believed that we could rely on the fact that the child devices would all be freed before the parent devices and thus we didn't need to worry about a release() function. While I still believe that the parent's "struct device" is guaranteed to outlive the child's "struct device" (because the child holds a kobject reference to the parent), the parent's "devm" allocated memory is a different story. That appears to be freed much earlier. Let's make this better for ti-sn65dsi86 by allocating each auxiliary with kzalloc and then free that memory in the release(). Fixes: bf73537f411b ("drm/bridge: ti-sn65dsi86: Break GPIO and MIPI-to-eDP bridge into sub-drivers") Suggested-by: Stephen Boyd Reviewed-by: Stephen Boyd Signed-off-by: Douglas Anderson Link: https://patchwork.freedesktop.org/patch/msgid/20230613065812.v2.1.I24b838a5b4151fb32bccd6f36397998ea2df9fbb@changeid Signed-off-by: Sasha Levin

drm: bridge: dw_hdmi: fix connector access for scdc

2023-07-23T11:53:35Z

[ Upstream commit 98703e4e061fb8715c7613cd227e32cdfd136b23 ] Commit 5d844091f237 ("drm/scdc-helper: Pimp SCDC debugs") changed the scdc interface to pick up an i2c adapter from a connector instead. However, in the case of dw-hdmi, the wrong connector was being used to pass i2c adapter information, since dw-hdmi's embedded connector structure is only populated when the bridge attachment callback explicitly asks for it. drm-meson is handling connector creation, so this won't happen, leading to a NULL pointer dereference. Fix it by having scdc functions access dw-hdmi's current connector pointer instead, which is assigned during the bridge enablement stage. Fixes: 5d844091f237 ("drm/scdc-helper: Pimp SCDC debugs") Signed-off-by: Adrián Larumbe Reported-by: Lukas F. Hartmann Acked-by: Neil Armstrong [narmstrong: moved Fixes tag before first S-o-b and added Reported-by tag] Signed-off-by: Neil Armstrong Link: https://patchwork.freedesktop.org/patch/msgid/20230601123153.196867-1-adrian.larumbe@collabora.com Signed-off-by: Sasha Levin

drm: bridge: samsung-dsim: Fix PMS Calculator on imx8m[mnp]

2023-07-19T14:35:52Z

[ Upstream commit 54f1a83c72250b182fa7722b0c5f6eb5e769598d ] According to Table 13-45 of the i.MX8M Mini Reference Manual, the min and max values for M and the frequency range for the VCO_out calculator were incorrect. This information was contradicted in other parts of the mini, nano and plus manuals. After reaching out to my NXP Rep, when confronting him about discrepencies in the Nano manual, he responded with: "Yes it is definitely wrong, the one that is part of the NOTE in MIPI_DPHY_M_PLLPMS register table against PMS_P, PMS_M and PMS_S is not correct. I will report this to Doc team, the one customer should be take into account is the Table 13-40 DPHY PLL Parameters and the Note above." These updated values also match what is used in the NXP downstream kernel. To fix this, make new variables to hold the min and max values of m and the minimum value of VCO_out, and update the PMS calculator to use these new variables instead of using hard-coded values to keep the backwards compatibility with other parts using this driver. Fixes: 4d562c70c4dc ("drm: bridge: samsung-dsim: Add i.MX8M Mini/Nano support") Signed-off-by: Adam Ford Reviewed-by: Lucas Stach Tested-by: Chen-Yu Tsai Tested-by: Frieder Schrempf Reviewed-by: Frieder Schrempf Tested-by: Marek Szyprowski Reviewed-by: Jagan Teki Tested-by: Jagan Teki # imx8mm-icore Signed-off-by: Neil Armstrong Link: https://patchwork.freedesktop.org/patch/msgid/20230526030559.326566-3-aford173@gmail.com Signed-off-by: Sasha Levin

drm/bridge: ti-sn65dsi83: Fix enable/disable flow to meet spec

2023-07-19T14:35:52Z

[ Upstream commit dd9e329af7236e34c566d3705ea32a63069b9b13 ] The datasheet describes the following initialization flow including minimum delay times between each step: 1. DSI data lanes need to be in LP-11 and the clock lane in HS mode 2. toggle EN signal 3. initialize registers 4. enable PLL 5. soft reset 6. enable DSI stream 7. check error status register To meet this requirement we need to make sure the host bridge's pre_enable() is called first by using the pre_enable_prev_first flag. Furthermore we need to split enable() into pre_enable() which covers steps 2-5 from above and enable() which covers step 7 and is called after the host bridge's enable(). Signed-off-by: Frieder Schrempf Fixes: ceb515ba29ba ("drm/bridge: ti-sn65dsi83: Add TI SN65DSI83 and SN65DSI84 driver") Tested-by: Alexander Stein #TQMa8MxML/MBa8Mx Reviewed-by: Neil Armstrong Signed-off-by: Neil Armstrong Link: https://patchwork.freedesktop.org/patch/msgid/20230503163313.2640898-3-frieder@fris.de Signed-off-by: Sasha Levin