kernel.git/drivers/bus/ti-sysc.c, branch linux-5.4.y

Revert "bus: ti-sysc: Probe for l4_wkup and l4_cfg interconnect devices first"

2025-06-27T10:02:55Z

[ Upstream commit 36305857b1ead8f6ca033a913162ebc09bee0b43 ] This reverts commit 4700a00755fb5a4bb5109128297d6fd2d1272ee6. It breaks target-module@2b300050 ("ti,sysc-omap2") probe on AM62x in a case when minimally-configured system tries to network-boot: [ 6.888776] probe of 2b300050.target-module returned 517 after 258 usecs [ 17.129637] probe of 2b300050.target-module returned 517 after 708 usecs [ 17.137397] platform 2b300050.target-module: deferred probe pending: (reason unknown) [ 26.878471] Waiting up to 100 more seconds for network. There are minimal configurations possible when the deferred device is not being probed any more (because everything else has been successfully probed) and deferral lists are not processed any more. Stable mmc enumeration can be achieved by filling /aliases node properly (4700a00755fb commit's rationale). After revert: [ 9.006816] IP-Config: Complete: [ 9.010058] device=lan0, ... Tested-by: Andreas Kemnade # GTA04, Panda, BT200 Reviewed-by: Tony Lindgren Signed-off-by: Alexander Sverdlin Link: https://lore.kernel.org/r/20250401090643.2776793-1-alexander.sverdlin@siemens.com Signed-off-by: Kevin Hilman Signed-off-by: Sasha Levin

bus: ti-sysc: Fix SYSC_QUIRK_SWSUP_SIDLE_ACT handling for uart wake-up

2023-10-10T19:46:39Z

[ Upstream commit e5deb8f76e64d94ccef715e75ebafffd0c312d80 ] The uarts should be tagged with SYSC_QUIRK_SWSUP_SIDLE instead of SYSC_QUIRK_SWSUP_SIDLE_ACT. The difference is that SYSC_QUIRK_SWSUP_SIDLE is used to force idle target modules rather than block idle during usage. The SYSC_QUIRK_SWSUP_SIDLE_ACT should disable autoidle and wake-up when a target module is active, and configure autoidle and wake-up when a target module is inactive. We are missing configuring the target module on sysc_disable_module(), and missing toggling of the wake-up bit. Let's fix the issue to allow uart wake-up to work. Fixes: fb685f1c190e ("bus: ti-sysc: Handle swsup idle mode quirks") Tested-by: Dhruva Gole Tested-by: Kevin Hilman Signed-off-by: Tony Lindgren Signed-off-by: Sasha Levin

bus: ti-sysc: Configure uart quirks for k3 SoC

2023-09-23T09:00:04Z

[ Upstream commit 03a711d3cb83692733f865312f49e665c49de6de ] Enable the uart quirks similar to the earlier SoCs. Let's assume we are likely going to need a k3 specific quirk mask separate from the earlier SoCs, so let's not start changing the revision register mask at this point. Note that SYSC_QUIRK_LEGACY_IDLE will be needed until we can remove the need for pm_runtime_irq_safe() from 8250_omap driver. Reviewed-by: Nishanth Menon Signed-off-by: Tony Lindgren Signed-off-by: Sasha Levin

bus: ti-sysc: Flush posted write on enable before reset

2023-08-30T14:27:17Z

[ Upstream commit 34539b442b3bc7d5bf10164750302b60b91f18a7 ] The am335x devices started producing boot errors for resetting musb module in because of subtle timing changes: Unhandled fault: external abort on non-linefetch (0x1008) ... sysc_poll_reset_sysconfig from sysc_reset+0x109/0x12 sysc_reset from sysc_probe+0xa99/0xeb0 ... The fix is to flush posted write after enable before reset during probe. Note that some devices also need to specify the delay after enable with ti,sysc-delay-us, but this is not needed for musb on am335x based on my tests. Reported-by: kernelci.org bot Closes: https://storage.kernelci.org/next/master/next-20230614/arm/multi_v7_defconfig+CONFIG_THUMB2_KERNEL=y/gcc-10/lab-cip/baseline-beaglebone-black.html Fixes: 596e7955692b ("bus: ti-sysc: Add support for software reset") Signed-off-by: Tony Lindgren Signed-off-by: Sasha Levin

bus: ti-sysc: Improve reset to work with modules with no sysconfig

2023-08-30T14:27:17Z

[ Upstream commit ab4d309d8708035bd323b2e2446eb68cda5e61e5 ] At least display susbsystem (DSS) has modules with no sysconfig registers and rely on custom function for module reset handling. Let's make reset work with that too. Signed-off-by: Tony Lindgren Stable-dep-of: 34539b442b3b ("bus: ti-sysc: Flush posted write on enable before reset") Signed-off-by: Sasha Levin

bus: ti-sysc: Fix warnings for unbind for serial

2022-06-14T16:11:54Z

[ Upstream commit c337125b8834f9719dfda0e40b25eaa266f1b8cf ] We can get "failed to disable" clock_unprepare warnings on unbind at least for the serial console device if the unbind is done before the device has been idled. As some devices are using deferred idle, we must check the status for pending idle work to idle the device. Fixes: 76f0f772e469 ("bus: ti-sysc: Improve handling for no-reset-on-init and no-idle-on-init") Cc: Romain Naour Reviewed-by: Romain Naour Signed-off-by: Tony Lindgren Link: https://lore.kernel.org/r/20220512053021.61650-1-tony@atomide.com Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin

bus: ti-sysc: Use CLKDM_NOAUTO for dra7 dcan1 for errata i893

2021-10-13T08:08:19Z

[ Upstream commit b13a270ace2e4c70653aa1d1d0394c553905802f ] Commit 94f6345712b3 ("bus: ti-sysc: Implement quirk handling for CLKDM_NOAUTO") should have also added the quirk for dra7 dcan1 in addition to dcan2 for errata i893 handling. Let's also pass the quirk flag for legacy mode booting for if "ti,hwmods" dts property is used with related dcan hwmod data. This should be only needed if anybody needs to git bisect earlier stable trees though. Fixes: 94f6345712b3 ("bus: ti-sysc: Implement quirk handling for CLKDM_NOAUTO") Signed-off-by: Tony Lindgren Signed-off-by: Sasha Levin

bus: ti-sysc: Fix flakey idling of uarts and stop using swsup_sidle_act

2021-06-10T11:37:08Z

[ Upstream commit c8692ad416dcc420ce1b403596a425c8f4c2720b ] Looks like the swsup_sidle_act quirk handling is unreliable for serial ports. The serial ports just eventually stop idling until woken up and re-idled again. As the serial port not idling blocks any deeper SoC idle states, it's adds an annoying random flakeyness for power management. Let's just switch to swsup_sidle quirk instead like we already do for omap3 uarts. This means we manually idle the port instead of trying to use the hardware autoidle features when not in use. For more details on why the serial ports have been using swsup_idle_act, see commit 66dde54e978a ("ARM: OMAP2+: hwmod-data: UART IP needs software control to manage sidle modes"). It seems that the swsup_idle_act quirk handling is not enough though, and for example the TI Android kernel changed to using swsup_sidle with commit 77c34c84e1e0 ("OMAP4: HWMOD: UART1: disable smart-idle."). Fixes: b4a9a7a38917 ("bus: ti-sysc: Handle swsup idle mode quirks") Cc: Carl Philipp Klemm Cc: Ivan Jelincic Cc: Merlijn Wajer Cc: Pavel Machek Cc: Sebastian Reichel Cc: Sicelo A. Mhlongo Signed-off-by: Tony Lindgren Signed-off-by: Sasha Levin

bus: ti-sysc: Probe for l4_wkup and l4_cfg interconnect devices first

2021-05-11T12:04:04Z

[ Upstream commit 4700a00755fb5a4bb5109128297d6fd2d1272ee6 ] We want to probe l4_wkup and l4_cfg interconnect devices first to avoid issues with missing resources. Otherwise we attempt to probe l4_per devices first causing pointless deferred probe and also annoyingh renumbering of the MMC devices for example. Signed-off-by: Tony Lindgren Signed-off-by: Sasha Levin

bus: ti-sysc: Fix warning on unbind if reset is not deasserted

2021-04-10T11:34:30Z

[ Upstream commit a7b5d7c4969aba8d1f04c29048906abaa71fb6a9 ] We currently get thefollowing on driver unbind if a reset is configured and asserted: WARNING: CPU: 0 PID: 993 at drivers/reset/core.c:432 reset_control_assert ... (reset_control_assert) from [] (sysc_remove+0x190/0x1e4) (sysc_remove) from [] (platform_remove+0x24/0x3c) (platform_remove) from [] (__device_release_driver+0x154/0x214) (__device_release_driver) from [] (device_driver_detach+0x3c/0x8c) (device_driver_detach) from [] (unbind_store+0x60/0xd4) (unbind_store) from [] (kernfs_fop_write_iter+0x10c/0x1cc) Let's fix it by checking the reset status. Signed-off-by: Tony Lindgren Signed-off-by: Sasha Levin