kernel.git/drivers/bluetooth/btbcm.c, branch linux-5.6.y

Bluetooth: btbcm : Fix warning about missing blank lines after declarations

2020-01-09T20:24:47Z

This patches fixes two warnings of checkpatch.pl, both of the type WARNING: Missing a blank line after declarations Signed-off-by: Changqi Du Signed-off-by: Marcel Holtmann

Bluetooth: btbcm: Support pcm configuration

2019-11-27T07:09:55Z

Add BCM vendor specific command to configure PCM parameters. The new vendor opcode allows us to set the sco routing, the pcm interface rate, and a few other pcm specific options (frame sync, sync mode, and clock mode). See broadcom-bluetooth.txt in Documentation for more information about valid values for those settings. Here is an example trace where this opcode was used to configure a BCM4354: < HCI Command: Vendor (0x3f|0x001c) plen 5 01 02 00 01 01 > HCI Event: Command Complete (0x0e) plen 4 Vendor (0x3f|0x001c) ncmd 1 Status: Success (0x00) We can read back the values as well with ocf 0x001d to confirm the values that were set: $ hcitool cmd 0x3f 0x001d < HCI Command: ogf 0x3f, ocf 0x001d, plen 0 > HCI Event: 0x0e plen 9 01 1D FC 00 01 02 00 01 01 Signed-off-by: Abhishek Pandit-Subedi Signed-off-by: Marcel Holtmann Signed-off-by: Johan Hedberg

Bluetooth: btbcm: Use the BDADDR_PROPERTY quirk

2019-11-22T12:35:20Z

Some devices ship with the controller default address, like the Orange Pi 3 (BCM4345C5). Allow the bootloader to set a valid address through the device tree. Signed-off-by: Andre Heider Signed-off-by: Marcel Holtmann

Bluetooth: btbcm: Add entry for BCM4335A0 UART bluetooth

2019-11-21T07:10:46Z

This patch adds the device ID for the BCM4335A0 module (part of the AMPAK AP6335 WIFI/Bluetooth combo) hciconfig output: ``` hci1: Type: Primary Bus: UART BD Address: 43:35:B0:07:1F:AC ACL MTU: 1021:8 SCO MTU: 64:1 UP RUNNING RX bytes:5079 acl:0 sco:0 events:567 errors:0 TX bytes:69065 acl:0 sco:0 commands:567 errors:0 Features: 0xbf 0xfe 0xcf 0xff 0xdf 0xff 0x7b 0x87 Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3 Link policy: RSWITCH SNIFF Link mode: SLAVE ACCEPT Name: 'alarm' Class: 0x000000 Service Classes: Unspecified Device Class: Miscellaneous, HCI Version: 4.0 (0x6) Revision: 0x161 LMP Version: 4.0 (0x6) Subversion: 0x4106 Manufacturer: Broadcom Corporation (15) ``` Signed-off-by: Mohammad Rasim Signed-off-by: Marcel Holtmann

Bluetooth: btbcm: Add entry for BCM4334B0 UART Bluetooth

2019-11-19T05:20:15Z

Add the device ID for the WiFi/BT/FM combo chip BCM4334 (rev B0). The chip seems to use 43:34:b0:00:00:00 as default address, so add it to the list of default addresses and leave it up to the user to configure a valid one. Signed-off-by: Stephan Gerhold Signed-off-by: Marcel Holtmann

bluetooth: bcm: Add support for loading firmware for BCM4345C5

2019-09-05T15:27:22Z

Detect BCM4345C5 and load a corresponding firmware file. Signed-off-by: Ondrej Jirman Signed-off-by: Marcel Holtmann

Bluetooth: btbcm: Add entry for BCM4359C0 UART bluetooth

2019-07-06T10:56:44Z

The BCM4359C0 BT/Wi-Fi compo chip needs an entry to be discovered by the btbcm driver. Tested using an AP6398S module from Ampak. Signed-off-by: Neil Armstrong Signed-off-by: Marcel Holtmann

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 156

2019-05-30T18:26:35Z

Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details you should have received a copy of the gnu general public license along with this program if not write to the free software foundation inc 59 temple place suite 330 boston ma 02111 1307 usa extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 1334 file(s). Signed-off-by: Thomas Gleixner Reviewed-by: Allison Randal Reviewed-by: Richard Fontana Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de Signed-off-by: Greg Kroah-Hartman

Bluetooth: btbcm: Add default address for BCM2076B1

2019-05-05T17:27:49Z

BCM2076B1 appears to use 20:76:A0:00:56:79 as default address. This address is used by at least 5 devices with the AMPAK AP6476 module and is also suspicious because it starts with the chip name 2076 (followed by a different revision A0 for some reason). Add it to the list of default addresses and leave it up to the user to configure a valid one. Signed-off-by: Stephan Gerhold Signed-off-by: Marcel Holtmann

Bluetooth: btbcm: Add entry for BCM2076B1 UART Bluetooth

2019-04-23T17:10:56Z

Add the device ID for the BT/FM/GPS combo chip BCM2076 (rev B1) used in the AMPAK AP6476 WiFi/BT/FM/GPS module. Signed-off-by: Stephan Gerhold Signed-off-by: Marcel Holtmann