kernel.git/drivers/bcma/host_pci.c, branch linux-4.0.y

bcma: implement host code support for PCIe Gen 2 devices

2015-01-29T08:54:43Z

This is stil incomplete, so we don't add PCI IDs of new devices yet. Purpose of this patch is to allow testing & adjusting rest of the code. Signed-off-by: Rafał Miłecki Signed-off-by: Kalle Valo

bcma: add another PCI ID of device with BCM43228

2014-10-23T18:02:06Z

It was found attached to the BCM47081A0 SoC. Log: bcma: bus0: Found chip with id 43228, rev 0x00 and package 0x08 Signed-off-by: Rafał Miłecki Signed-off-by: John W. Linville

bcma: move bus struct setup into early part of host specific code

2014-09-09T19:27:18Z

This change is important for SoC host. In future we will want to know chip ID (needed for early MIPS boot) before doing cores scanning. Signed-off-by: Rafał Miłecki Acked-by: Hauke Mehrtens Signed-off-by: John W. Linville

bcma: add PCI ID for spromless BCM43217

2014-08-25T19:39:23Z

This adds the PCI ID a BCM43217 without a sprom. This devices was found on a Netgear R6250 attached to a BCM4708 ARM SoC. bcma: bus1: Found chip with id 0xA8D1, rev 0x00 and package 0x08 bcma: bus1: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x27, class 0x0) bcma: bus1: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x1E, class 0x0) bcma: bus1: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x14, class 0x0) b43-phy0: Broadcom 43217 WLAN found (core revision 30) b43-phy0: Found PHY: Analog 9, Type 4 (N), Revision 17 b43-phy0: Found Radio: Manuf 0x17F, ID 0x2057, Revision 14, Version 1 Signed-off-by: Hauke Mehrtens Signed-off-by: John W. Linville

bcma: add support for BCM43131 that was found in Tenda W311E

2014-07-29T14:32:57Z

Signed-off-by: Rafał Miłecki Signed-off-by: John W. Linville

bcma: add support for BCM43217 found in Tenda W322E (14e4:43a9)

2014-07-18T17:45:24Z

Signed-off-by: Rafał Miłecki Signed-off-by: John W. Linville

bcma: pci: remove DEFINE_PCI_DEVICE_TABLE macro

2013-12-09T20:35:27Z

Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro is not preferred. Signed-off-by: Jingoo Han Signed-off-by: John W. Linville

bcma: pci: remove unnecessary pci_set_drvdata()

2013-12-05T19:56:39Z

The driver core clears the driver data to NULL after device_release or on probe failure. Thus, it is not needed to manually clear the device driver data to NULL. Signed-off-by: Jingoo Han Signed-off-by: John W. Linville

bcma: add PCI id 0x4313

2013-10-10T17:46:00Z

This PCI id is used by some BCM4313 cards without a sprom. I have seen such a card on a router connected to some BCM63XX SoC via PCIe. There are cards out there with the same PCI id and a BCM4311, which is a pre ieee80211n chip only supporting ieee80211a, these are still not supported by b43 and not detected by ssb. This devices was found by someone in this ticket: https://dev.openwrt.org/ticket/13551 Signed-off-by: Hauke Mehrtens Signed-off-by: John W. Linville

bcma: reject PCI cards in bcma.

2013-10-10T17:46:00Z

bcma currently only supports PCIe cards and no PCI cards, reject them if we find them. I have never heard of any PCI card using the AI bus (bcma), all of them are using ssb instead. Signed-off-by: Hauke Mehrtens Signed-off-by: John W. Linville