kernel.git/drivers/ata/libata-eh.c, branch linux-2.6.23.y

libata: backport ATA_FLAG_NO_SRST and ATA_FLAG_ASSUME_ATA

2007-11-16T17:30:25Z

Differs from mainline, but the functionality is already there. Backport ATA_FLAG_NO_SRST and ATA_FLAG_ASSUME_ATA. These are originally link flags (ATA_LFLAG_*) but link abstraction doesn't exist on 2.6.23, so make it port flags. This is for the following workaround for ASUS P5W DH Deluxe. These new flags don't introduce any behavior change unless set and nobody sets them yet. Signed-off-by: Tejun Heo Cc: Jeff Garzik Signed-off-by: Greg Kroah-Hartman

libata: implement EH fast drain

2007-07-20T12:26:26Z

In most cases, when EH is scheduled, all in-flight commands are aborted causing EH to kick in immediately. However, in some cases (especially with PMP), it's unclear which commands are affected by the error condition and although aborting all in-flight commands work, it isn't optimal and may cause unnecessary disruption. On the other hand, waiting for in-flight commands to drain themselves can take up to 30seconds. This patch implements EH fast drain to handle such situations. It gives in-flight commands some time to finish up but doesn't wait for too long. After EH is scheduled, fast drain timer is started and if no other completion occurs in ATA_EH_FASTDRAIN_INTERVAL all in-flight commands are aborted. If any completion occurred in the interval, the port is given another interval to finish up itself. Currently ATA_EH_FASTDRAIN_INTERVAL is 3 secs which should be enough for finishing up most commands. Signed-off-by: Tejun Heo Signed-off-by: Jeff Garzik

libata: schedule probing after SError access failure during autopsy

2007-07-20T12:26:26Z

If SError isn't accessible, EH can't tell whether hotplug has happened or not. Report SError read failure with AC_ERR_OTHER and schedule probing with hardreset. This will be mainly useful for PMPs. Signed-off-by: Tejun Heo Signed-off-by: Jeff Garzik

libata: clear HOTPLUG flag after a reset

2007-07-20T12:26:25Z

ATA_EHI_HOTPLUGGED is a hint for reset functions indicating the the port might have gone through hotplug/unplug just before entering EH. Reset functions modify their behaviors a bit to handle the situation better - e.g. using longer debouncing delay. Currently, once HOTPLUG is set, it isn't cleared till the end of EH. This is unnecessary and makes EH take longer. Clear the HOTPLUGGED flag after a reset try (successful or not). Signed-off-by: Tejun Heo Signed-off-by: Jeff Garzik

libata: quickly trigger SATA SPD down after debouncing failed

2007-07-20T12:19:06Z

Debouncing failure is a good indicator of basic link problem. Use -EPIPE to indicate debouncing failure and make ata_eh_reset() invoke sata_down_spd_limit() if the error occurs during reset. Signed-off-by: Tejun Heo Signed-off-by: Jeff Garzik

libata: improve SATA PHY speed down logic

2007-07-20T12:19:05Z

sata_down_spd_limit() first reads the current SPD from SStatus and limit the speed to the lower one of one below the current limit or one below the current SPD in SStatus. SPD may not be accessible or valid when SPD down is requested making sata_down_spd_limit() fail when it's most needed. This patch makes the current SPD cached after each successful reset and forces GEN I speed (1.5Gbps) if neither of SStatus or the cached value is valid, so sata_down_spd_limit() is now guaranteed to lower the speed limit if lower speed is available. Signed-off-by: Tejun Heo Signed-off-by: Jeff Garzik

libata: implement AC_ERR_NCQ

2007-07-20T12:02:11Z

When an NCQ command fails, all commands in flight are aborted and the offending one is reported using log page 10h. Depending on controller characteristics and LLD implementation, all commands may appear as having a device error due to shared TF status making it hard to determine what's actually going on. This patch adds AC_ERR_NCQ, marks the command reported by log page 10h with it and print extra "" after the error report for the command to help distinguishing the offending command. Signed-off-by: Tejun Heo Signed-off-by: Jeff Garzik

libata: improve EH report formatting

2007-07-20T12:02:11Z

Requiring LLDs to format multiple error description messages properly doesn't work too well. Help LLDs a bit by making ata_ehi_push_desc() insert ", " on each invocation. __ata_ehi_push_desc() is the raw version without the automatic separator. While at it, make ehi_desc interface proper functions instead of macros. Signed-off-by: Tejun Heo Signed-off-by: Jeff Garzik

libata-link: separate out ata_eh_handle_dev_fail()

2007-07-11T01:46:03Z

Separate out ata_eh_handle_dev_fail() from ata_eh_recover(). This is in preparation of ata_link and PMP support. Signed-off-by: Tejun Heo Signed-off-by: Jeff Garzik

libata-acpi: implement _GTM/_STM support

2007-07-09T16:17:32Z

Implement _GTM/_STM support. acpi_gtm is added to ata_port which stores _GTM parameters over suspend/resume cycle. A new hook ata_acpi_on_suspend() is responsible for storing _GTM parameters during suspend. _STM is executed in ata_acpi_on_resume(). With this change, invoking _GTF is safe on IDE hierarchy and acpi_sata check before _GTF is removed. ata_acpi_gtm() and ata_acpi_stm() implementation is taken from Alan Cox's pata_acpi implementation. ata_acpi_gtm() is fixed such that the result parameter is not shifted by sizeof(union acpi_object). Signed-off-by: Tejun Heo Cc: Alan Cox Signed-off-by: Jeff Garzik