kernel.git/drivers/acpi/device_pm.c, branch linux-5.4.y

PM: ACPI: PCI: Drop acpi_pm_set_bridge_wakeup()

2020-12-30T10:51:32Z

commit 7482c5cb90e5a7f9e9e12dd154d405e0219656e3 upstream. The idea behind acpi_pm_set_bridge_wakeup() was to allow bridges to be reference counted for wakeup enabling, because they may be enabled to signal wakeup on behalf of their subordinate devices and that may happen for multiple times in a row, whereas for the other devices it only makes sense to enable wakeup signaling once. However, this becomes problematic if the bridge itself is suspended, because it is treated as a "regular" device in that case and the reference counting doesn't work. For instance, suppose that there are two devices below a bridge and they both can signal wakeup. Every time one of them is suspended, wakeup signaling is enabled for the bridge, so when they both have been suspended, the bridge's wakeup reference counter value is 2. Say that the bridge is suspended subsequently and acpi_pci_wakeup() is called for it. Because the bridge can signal wakeup, that function will invoke acpi_pm_set_device_wakeup() to configure it and __acpi_pm_set_device_wakeup() will be called with the last argument equal to 1. This causes __acpi_device_wakeup_enable() invoked by it to omit the reference counting, because the reference counter of the target device (the bridge) is 2 at that time. Now say that the bridge resumes and one of the device below it resumes too, so the bridge's reference counter becomes 0 and wakeup signaling is disabled for it, but there is still the other suspended device which may need the bridge to signal wakeup on its behalf and that is not going to work. To address this scenario, use wakeup enable reference counting for all devices, not just for bridges, so drop the last argument from __acpi_device_wakeup_enable() and __acpi_pm_set_device_wakeup(), which causes acpi_pm_set_device_wakeup() and acpi_pm_set_bridge_wakeup() to become identical, so drop the latter and use the former instead of it everywhere. Fixes: 1ba51a7c1496 ("ACPI / PCI / PM: Rework acpi_pci_propagate_wakeup()") Signed-off-by: Rafael J. Wysocki Reviewed-by: Mika Westerberg Acked-by: Bjorn Helgaas Cc: 4.14+ # 4.14+ Signed-off-by: Greg Kroah-Hartman

ACPI: PM: Avoid using power resources if there are none for D0

2020-06-17T14:40:28Z

commit 956ad9d98b73f59e442cc119c98ba1e04e94fe6d upstream. As recently reported, some platforms provide a list of power resources for device power state D3hot, through the _PR3 object, but they do not provide a list of power resources for device power state D0. Among other things, this causes acpi_device_get_power() to return D3hot as the current state of the device in question if all of the D3hot power resources are "on", because it sees the power_resources flag set and calls acpi_power_get_inferred_state() which finds that D3hot is the shallowest power state with all of the associated power resources turned "on", so that's what it returns. Moreover, that value takes precedence over the acpi_dev_pm_explicit_get() return value, because it means a deeper power state. The device may very well be in D0 physically at that point, however. Moreover, the presence of _PR3 without _PR0 for a given device means that only one D3-level power state can be supported by it. Namely, because there are no power resources to turn "off" when transitioning the device from D0 into D3cold (which should be supported since _PR3 is present), the evaluation of _PS3 should be sufficient to put it straight into D3cold, but this means that the effect of turning "on" the _PR3 power resources is unclear, so it is better to avoid doing that altogether. Consequently, there is no practical way do distinguish D3cold from D3hot for the device in question and the power states of it can be labeled so that D3hot is the deepest supported one (and Linux assumes that putting a device into D3hot via ACPI may cause power to be removed from it anyway, for legacy reasons). To work around the problem described above modify the ACPI enumeration of devices so that power resources are only used for device power management if the list of D0 power resources is not empty and make it mart D3cold as supported only if that is the case and the D3hot list of power resources is not empty too. Fixes: ef85bdbec444 ("ACPI / scan: Consolidate extraction of power resources lists") Link: https://bugzilla.kernel.org/show_bug.cgi?id=205057 Link: https://lore.kernel.org/linux-acpi/20200603194659.185757-1-hdegoede@redhat.com/ Reported-by: Hans de Goede Tested-by: Hans de Goede Tested-by: youling257@gmail.com Cc: 3.10+ # 3.10+ Signed-off-by: Rafael J. Wysocki Reviewed-by: Hans de Goede Signed-off-by: Greg Kroah-Hartman

PM: ACPI: Output correct message on target power state

2020-05-06T06:15:09Z

commit a9b760b0266f563b4784f695bbd0e717610dc10a upstream. Transitioned power state logged at the end of setting ACPI power. However, D3cold won't be in the message because state can only be D3hot at most. Use target_state to corretly report when power state is D3cold. Cc: All applicable Signed-off-by: Kai-Heng Feng Signed-off-by: Rafael J. Wysocki Signed-off-by: Greg Kroah-Hartman

ACPI: PM: Avoid attaching ACPI PM domain to certain devices

2019-12-17T18:56:35Z

commit b9ea0bae260f6aae546db224daa6ac1bd9d94b91 upstream. Certain ACPI-enumerated devices represented as platform devices in Linux, like fans, require special low-level power management handling implemented by their drivers that is not in agreement with the ACPI PM domain behavior. That leads to problems with managing ACPI fans during system-wide suspend and resume. For this reason, make acpi_dev_pm_attach() skip the affected devices by adding a list of device IDs to avoid to it and putting the IDs of the affected devices into that list. Fixes: e5cc8ef31267 (ACPI / PM: Provide ACPI PM callback routines for subsystems) Reported-by: Zhang Rui Tested-by: Todd Brandt Cc: 3.10+ # 3.10+ Signed-off-by: Rafael J. Wysocki Signed-off-by: Greg Kroah-Hartman

Merge branches 'pm-opp', 'pm-qos', 'acpi-pm', 'pm-domains' and 'pm-tools'

2019-09-17T07:49:19Z

* pm-opp: PM / OPP: Correct Documentation about library location opp: of: Support multiple suspend OPPs defined in DT dt-bindings: opp: Support multiple opp-suspend properties opp: core: add regulators enable and disable opp: Don't decrement uninitialized list_kref * pm-qos: PM: QoS: Get rid of unused flags * acpi-pm: ACPI: PM: Print debug messages on device power state changes * pm-domains: PM / Domains: Verify PM domain type in dev_pm_genpd_set_performance_state() PM / Domains: Simplify genpd_lookup_dev() PM / Domains: Align in-parameter names for some genpd functions * pm-tools: pm-graph: make setVal unbuffered again for python2 and python3 cpupower: update German translation tools/power/cpupower: fix 64bit detection when cross-compiling cpupower: Add missing newline at end of file pm-graph v5.5

PM / wakeup: Show wakeup sources stats in sysfs

2019-08-20T22:20:40Z

Add an ID and a device pointer to 'struct wakeup_source'. Use them to to expose wakeup sources statistics in sysfs under /sys/class/wakeup/wakeup/*. Co-developed-by: Greg Kroah-Hartman Signed-off-by: Greg Kroah-Hartman Co-developed-by: Stephen Boyd Signed-off-by: Stephen Boyd Signed-off-by: Tri Vo Tested-by: Kalesh Singh Signed-off-by: Rafael J. Wysocki

ACPI: PM: Print debug messages on device power state changes

2019-08-08T09:32:51Z

Add an acpi_handle_debug() statement to acpi_device_set_power() to allow ACPI device power state changes to be tracked. Signed-off-by: Rafael J. Wysocki

ACPI: PM: Fix regression in acpi_device_set_power()

2019-08-01T21:39:17Z

Commit f850a48a0799 ("ACPI: PM: Allow transitions to D0 to occur in special cases") overlooked the fact that acpi_power_transition() may change the power.state value for the target device and if that happens, it may confuse acpi_device_set_power() and cause it to omit the _PS0 evaluation which on some systems is necessary to change power states of devices from low-power to D0. Fix that by saving the current value of power.state for the target device before passing it to acpi_power_transition() and using the saved value in a subsequent check. Fixes: f850a48a0799 ("ACPI: PM: Allow transitions to D0 to occur in special cases") Reported-by: Kai-Heng Feng Reported-by: Mario Limonciello Signed-off-by: Rafael J. Wysocki Tested-by: Kai-Heng Feng Tested-by: Mario Limonciello

Merge branch 'pm-sleep'

2019-07-08T08:51:25Z

* pm-sleep: PM: sleep: Drop dev_pm_skip_next_resume_phases() ACPI: PM: Drop unused function and function header ACPI: PM: Introduce "poweroff" callbacks for ACPI PM domain and LPSS ACPI: PM: Simplify and fix PM domain hibernation callbacks PCI: PM: Simplify bus-level hibernation callbacks PM: ACPI/PCI: Resume all devices during hibernation kernel: power: swap: use kzalloc() instead of kmalloc() followed by memset() PM: sleep: Update struct wakeup_source documentation drivers: base: power: remove wakeup_sources_stats_dentry variable PM: suspend: Rename pm_suspend_via_s2idle() PM: sleep: Show how long dpm_suspend_start() and dpm_suspend_end() take PM: hibernate: powerpc: Expose pfn_is_nosave() prototype

Merge branches 'acpi-pm' and 'pm-pci'

2019-07-08T08:49:36Z

* acpi-pm: ACPI: PM: Make acpi_sleep_state_supported() non-static ACPI: PM: Allow transitions to D0 to occur in special cases ACPI: PM: Avoid evaluating _PS3 on transitions from D3hot to D3cold ACPI / sleep: Switch to use acpi_dev_get_first_match_dev() ACPI / LPIT: Correct LPIT end address for lpit_process() * pm-pci: ACPI: PM: Unexport acpi_device_get_power() PCI: PM/ACPI: Refresh all stale power state data in pci_pm_complete() PCI / ACPI: Add _PR0 dependent devices ACPI / PM: Introduce concept of a _PR0 dependent device PCI / ACPI: Use cached ACPI device state to get PCI device power state PCI: Do not poll for PME if the device is in D3cold PCI: Add missing link delays required by the PCIe spec PCI: PM: Replace pci_dev_keep_suspended() with two functions PCI: PM: Avoid resuming devices in D3hot during system suspend