kernel.git/arch/sh/cchips, branch linux-2.6.25.y

sh: Kill off more dead symbols.

2008-02-14T05:22:12Z

Reported-by: Robert P. J. Day Signed-off-by: Paul Mundt

sh: remove voyagergx

2008-01-28T04:19:03Z

This patch removes redundant irq handling code together with unused consistent alloc code. R2D uart setup code is changed to use sm501-regs.h and unused header files are removed. Signed-off-by: Magnus Damm Signed-off-by: Paul Mundt

sh: intc - remove default interrupt priority tables

2008-01-28T04:19:02Z

This patch removes interrupt priority tables from the intc code. Optimal priority assignment varies with embedded application anyway, so keeping the interrupt priority tables together with cpu-specific code doesn't make sense. The function intc_set_priority() should be used instead to set the desired interrupt priority level. Signed-off-by: Magnus Damm Signed-off-by: Paul Mundt

sh: Add -Werror for clean directories.

2007-11-07T02:13:55Z

Follow the MIPS and sparc64 changes for -Werror instrumentation. Signed-off-by: Paul Mundt

sh: cleanup struct irqaction initializers.

2007-10-03T06:04:08Z

Signed-off-by: Thomas Gleixner Signed-off-by: Andrew Morton Signed-off-by: Paul Mundt

sh: hd64461: Trivial build fixes for SH7709.

2007-09-21T02:57:53Z

Some trivial fixes to get SH7709 + HD64461 building again. Signed-off-by: Kristoffer Ericson Signed-off-by: Paul Mundt

sh: intc - mark data structures as __initdata

2007-09-21T02:57:50Z

With the intc core improved it is now possible to put the intc data structures in the initdata section. Version two of this patch puts the __initdata inside DECLARE_INTC_DESC() and removes the __initdata included in the board specific r2d code. Signed-off-by: Magnus Damm Signed-off-by: Paul Mundt

sh: replace sh specific CONFIG_VOYAGERGX with CONFIG_MFD_SM501

2007-09-21T02:57:50Z

This patch replaces all instances of CONFIG_VOYAGERGX with CONFIG_MFD_SM501. While at it we make sure the r2d code compiles both with and without SM501. Signed-off-by: Magnus Damm Signed-off-by: Paul Mundt

sh: intc - rework core code

2007-09-21T02:57:50Z

This patch reworks the intc core, implementing the following features: - Support dual priority registers - one set and one clear register - All 8/16/32 bit register combinations are now supported - Both single mask and single enable bitmap register are supported - Add code to set interrupt priority - Speedup sense and priority configuration code - Allocate data using bootmem, allows intc data structures to be __initdata - Save memory - allocated memory footprint is smaller than intc structures Signed-off-by: Magnus Damm Signed-off-by: Paul Mundt

sh: intc - convert voyagergx code

2007-09-21T02:57:48Z

This patch converts the sh-specific voyagergx interrupt code to make use of intc. A lot of "interesting" old cruft gets replaced with intc tables and some simple demux code. - All interrupt sources in the sm501 data sheet are now in the header. - The number and order of IRQ values are disconnected from register bits. - Interrupt sources now start from IRQ 200. - set_irq_chained_handler() is now used to hook up the demux function. In the future it would probably make sense to move the interrupt demuxer into into the mfd driver, but this is probably a nice step in the right direction until that happens. Tested on a R2D-1 board using the serial port hooked up to the sm501. Signed-off-by: Magnus Damm Signed-off-by: Paul Mundt