kernel.git/arch/powerpc/boot/Makefile, branch linux-2.6.25.y

[POWERPC] Fix build failure for tqm8540 and sbc85xx defconfigs

2008-03-19T23:15:00Z

The wrapper script didn't have entries for the TQM8540 board and the SBC8548 or SBC8560 boards. I've assumed that the TQM8540 console is 8250 based and not CPM based by looking at its defconfig. There was also a trailing * on the TQM8555 entry that I removed too. Signed-off-by: Paul Gortmaker Signed-off-by: Grant Likely Signed-off-by: Paul Mackerras

[POWERPC] Fix zImage-dtb.initrd build error

2008-03-12T23:09:26Z

The pattern substitution rules were failing when used with zImage-dtb targets. If zImage-dtb.initrd was selected, the pattern substitution would generate "zImage.initrd-dtb" instead of "zImage-dtb.initrd" which caused the build to fail. This renames zImage-dtb to dtbImage to avoid the problem entirely. By not using the zImage prefix then is no potential for namespace collisions. Signed-off-by: Grant Likely Acked-by: Geoff Levand Signed-off-by: Paul Mackerras

[POWERPC] Fix bootwrapper builds with older gcc versions

2008-02-20T02:33:37Z

GCC versions before 3.4 did not support the -mcpu=440 option. Use -mcpu=405 for the 4xx specific bootwrapper files, as that has been around for much longer. Signed-off-by: Josh Boyer Signed-off-by: Paul Mackerras

[POWERPC] Remove generated files on make clean

2008-02-14T11:11:02Z

vmlinux.lds and dtc-parser.tab.h get created but never cleaned up. Signed-off-by: Paul Mackerras

[POWERPC] bootwrapper: Build multiple cuImages

2008-02-07T00:40:19Z

Currently, the kernel uses CONFIG_DEVICE_TREE to wrap a kernel image with a fdt blob which means for any given configuration only one dts file can be selected and so support for only one board can be built This moves the selection of the default .dts file out of the kernel config and into the bootwrapper makefile. The makefile chooses which images to build based on the kernel config and the dts source file name is taken directly from the image name. For example "cuImage.ebony" will use "ebony.dts" as the device tree source file. In addition, this patch allows a specific image to be requested from the command line by adding "cuImage.%" and "treeImage.%" targets to the list of valid built targets in arch/powerpc/Makefile. This allows the default dts selection to be overridden. Another advantage to this change is it allows a single defconfig to be supplied for all boards using the same chip family and only differing in the device tree. Important note: This patch adds two new zImage targets; zImage.dtb.% and zImage.dtb.initrd.% for zImages with embedded dtb files. Currently there are 5 platforms which require this: ps3, ep405, mpc885ads, ep88xc, adder875-redboot and ep8248e. This patch *changes the zImage filenames* for those platforms. ie. 'zImage.ps3' is now 'zImage.dtb.ps3'. This new zImage.dtb targets were added so that the .dts file could be part of the dependancies list for building them. Signed-off-by: Grant Likely Signed-off-by: Paul Mackerras

Merge branch 'linux-2.6'

2008-01-31T00:25:51Z

remove __attribute_used__

2008-01-28T22:21:18Z

Remove the deprecated __attribute_used__. [Introduce __section in a few places to silence checkpatch /sam] Signed-off-by: Adrian Bunk Signed-off-by: Sam Ravnborg

[POWERPC] Add a cuboot wrapper for 85xx with CPM2

2008-01-27T20:10:36Z

The bd info struct changes if we have CPM2 enabled in u-boot. Signed-off-by: Kumar Gala

[POWERPC] 4xx: PIKA Warp bootwrapper

2008-01-25T13:12:35Z

Add the cuboot wrapper for the PIKA Warp board Signed-off-by: Sean MacLennan Signed-off-by: Josh Boyer

[POWERPC] Add initial iomega StorCenter board port.

2008-01-24T01:54:36Z

Use cuImage bootwrapper until U-Boot port is completed. Derived heavily from Linkstation port. Signed-off-by: Jon Loeliger Acked-by: Andy Wilcox Signed-off-by: Kumar Gala