kernel.git/arch/mips/alchemy/devboards, branch linux-2.6.34.y

MIPS: DB1200: PCMCIA card detection must not be auto-enabled.

2010-04-30T19:52:43Z

Same issues as SD card detection: One of both is always triggering and the handlers take care to shut it up and enable the other. To avoid messages about "unbalanced interrupt enable/disable" they must not be automatically enabled when initally requested. This was not an issue with the db1200_defconfig due to fortunate timings; on a build without network chip support the warnings appear. Signed-off-by: Manuel Lauss To: Linux-MIPS Patchwork: http://patchwork.linux-mips.org/patch/1133/ Signed-off-by: Ralf Baechle

MIPS: Alchemy: DB1200: Remove custom wait implementation

2010-04-12T16:26:22Z

While playing with the out-of-tree MAE driver module, the system would panic after a while in the db1200 custom wait code after wakeup due to a clobbered k0 register being used as target address of a store op. Remove the custom wait implementation and revert back to the Alchemy- recommended implementation already set as default. Signed-off-by: Manuel Lauss To: Linux-MIPS Patchwork: http://patchwork.linux-mips.org/patch/1092/ Signed-off-by: Ralf Baechle

MIPS: Alchemy: Repair db1500/bosporus builds

2010-02-27T11:53:45Z

A few hunks somehow ended up outside their #ifdef/endif blocks, leading to -Werror-induces build failures. Signed-off-by: Manuel Lauss To: Linux-MIPS Patchwork: http://patchwork.linux-mips.org/patch/1003/ Signed-off-by: Ralf Baechle

MIPS: Alchemy: use 36bit addresses for PCMCIA resources.

2010-02-27T11:53:43Z

On Alchemy the PCMCIA area lies at the end of the chips 36bit system bus area. Currently, addresses at the far end of the 32bit area are assumed to belong to the PCMCIA area and fixed up to the real 36bit address before being passed to ioremap(). A previous commit enabled 64 bit physical size for the resource datatype on Alchemy and this allows to use the correct 36bit addresses when registering the PCMCIA sockets. This patch removes the 32-to-36bit address fixup and registers the Alchemy demo board pcmcia socket with the correct 36bit physical addresses. Tested on DB1200, with a CF card (ide-cs driver) and a 3c589 PCMCIA ethernet card. Signed-off-by: Manuel Lauss To: Linux-MIPS Cc: Manuel Lauss Patchwork: http://patchwork.linux-mips.org/patch/994/ Signed-off-by: Ralf Baechle

MIPS: Alchemy: devboard PM needs to save CPLD registers.

2010-02-27T11:53:41Z

Save/restore CPLD registers when doing suspend-to-ram; this fixes issues with harddisk and ethernet not working correctly when resuming on DB1200. Signed-off-by: Manuel Lauss To: Linux-MIPS Patchwork: http://patchwork.linux-mips.org/patch/986/ Signed-off-by: Ralf Baechle

MIPS: Alchemy: Remove forced command line setting

2010-02-27T11:53:20Z

It is not always used, even if it is available. Signed-off-by: Yoichi Yuasa Cc: linux-mips Patchwork: http://patchwork.linux-mips.org/patch/893/ Signed-off-by: Ralf Baechle

MIPS: Alchemy: get rid of common/reset.c

2010-02-27T11:53:04Z

Implement reset / poweroff in the board code instead. The peripheral reset code is gone too since YAMON which all in-tree boards use does the same work when it boots. Signed-off-by: Manuel Lauss Signed-off-by: Yoichi Yuasa Cc: Linux-MIPS Patchwork: http://patchwork.linux-mips.org/patch/783/ Patchwork: http://patchwork.linux-mips.org/patch/882/ Signed-off-by: Ralf Baechle

MIPS: Alchemy: Add au1000-eth platform device

2010-02-27T11:53:01Z

This patch makes the board code register the au1000-eth platform device. The au1000-eth platform data can be overriden with the au1xxx_override_eth_cfg function like it has to be done for the Bosporus board which uses a different MAC/PHY setup. Signed-off-by: Florian Fainelli Cc: David Miller Cc: linux-mips@linux-mips.org Cc: netdev@vger.kernel.org Patchwork: http://patchwork.linux-mips.org/patch/618/ Signed-off-by: Ralf Baechle

MIPS/SOUND: Alchemy: DB1200 AC97+I2S audio support.

2010-02-27T11:53:01Z

Machine driver for DB1200 AC97 and I2S audio systems, intended as a proper reference asoc machine for Alchemy-based systems. AC97/I2S can be selected at boot time by setting switch S6.7. Signed-off-by: Manuel Lauss Cc: Linux-MIPS Cc: alsa-devel@alsa-project.org Cc: Mark Brown Acked-by: Mark Brown Signed-off-by: Ralf Baechle

MIPS: Alchemy: Extended DB1200 board support.

2010-02-27T11:53:00Z

Create own directory for DB1200 code and update it with new features. - SPI support: - tmp121 temperature sensor - SPI flash on DB1200 - I2C support - NE1619 sensor - AT24 eeprom - I2C/SPI can be selected at boot time via switch S6.8 - Carddetect IRQs for SD cards. - gen_nand based NAND support. - hexleds count sleep/wake transitions. Signed-off-by: Manuel Lauss Cc: Linux-MIPS Signed-off-by: Ralf Baechle