kernel.git/arch/m68k/mac, branch linux-5.4.y

m68k: mac: Fix macintosh_config for Mac II

2025-06-27T10:02:45Z

[ Upstream commit 52ae3f5da7e5adbe3d1319573b55dac470abb83c ] When booted on my Mac II, the kernel prints this: Detected Macintosh model: 6 Apple Macintosh Unknown The catch-all entry ("Unknown") is mac_data_table[0] which is only needed in the unlikely event that the bootinfo model ID can't be matched. When model ID is 6, the search should begin and end at mac_data_table[1]. Fix the off-by-one error that causes this problem. Cc: Joshua Thompson Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Finn Thain Reviewed-by: Geert Uytterhoeven Link: https://lore.kernel.org/d0f30a551064ca4810b1c48d5a90954be80634a9.1745453246.git.fthain@linux-m68k.org Signed-off-by: Geert Uytterhoeven Signed-off-by: Sasha Levin

m68k: mac: Fix reboot hang on Mac IIci

2024-06-16T11:28:37Z

[ Upstream commit 265a3b322df9a973ff1fc63da70af456ab6ae1d6 ] Calling mac_reset() on a Mac IIci does reset the system, but what follows is a POST failure that requires a manual reset to resolve. Avoid that by using the 68030 asm implementation instead of the C implementation. Apparently the SE/30 has a similar problem as it has used the asm implementation since before git. This patch extends that solution to other systems with a similar ROM. After this patch, the only systems still using the C implementation are 68040 systems where adb_type is either MAC_ADB_IOP or MAC_ADB_II. This implies a 1 MiB Quadra ROM. This now includes the Quadra 900/950, which previously fell through to the "should never get here" catch-all. Reported-and-tested-by: Stan Johnson Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Finn Thain Reviewed-by: Geert Uytterhoeven Link: https://lore.kernel.org/r/480ebd1249d229c6dc1f3f1c6d599b8505483fd8.1714797072.git.fthain@linux-m68k.org Signed-off-by: Geert Uytterhoeven Signed-off-by: Sasha Levin

m68k: mac: Fix IOP status/control register writes

2020-08-19T06:15:56Z

[ Upstream commit 931fc82a6aaf4e2e4a5490addaa6a090d78c24a7 ] When writing values to the IOP status/control register make sure those values do not have any extraneous bits that will clear interrupt flags. To place the SCC IOP into bypass mode would be desirable but this is not achieved by writing IOP_DMAINACTIVE | IOP_RUN | IOP_AUTOINC | IOP_BYPASS to the control register. Drop this ineffective register write. Remove the flawed and unused iop_bypass() function. Make use of the unused iop_stop() function. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Finn Thain Tested-by: Stan Johnson Cc: Joshua Thompson Link: https://lore.kernel.org/r/09bcb7359a1719a18b551ee515da3c4c3cf709e6.1590880333.git.fthain@telegraphics.com.au Signed-off-by: Geert Uytterhoeven Signed-off-by: Sasha Levin

m68k: mac: Don't send IOP message until channel is idle

2020-08-19T06:15:56Z

[ Upstream commit aeb445bf2194d83e12e85bf5c65baaf1f093bd8f ] In the following sequence of calls, iop_do_send() gets called when the "send" channel is not in the IOP_MSG_IDLE state: iop_ism_irq() iop_handle_send() (msg->handler)() iop_send_message() iop_do_send() Avoid this by testing the channel state before calling iop_do_send(). When sending, and iop_send_queue is empty, call iop_do_send() because the channel is idle. If iop_send_queue is not empty, iop_do_send() will get called later by iop_handle_send(). Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Finn Thain Tested-by: Stan Johnson Cc: Joshua Thompson Link: https://lore.kernel.org/r/6d667c39e53865661fa5a48f16829d18ed8abe54.1590880333.git.fthain@telegraphics.com.au Signed-off-by: Geert Uytterhoeven Signed-off-by: Sasha Levin

m68k: mac: Don't call via_flush_cache() on Mac IIfx

2020-06-22T07:31:08Z

[ Upstream commit bcc44f6b74106b31f0b0408b70305a40360d63b7 ] There is no VIA2 chip on the Mac IIfx, so don't call via_flush_cache(). This avoids a boot crash which appeared in v5.4. printk: console [ttyS0] enabled printk: bootconsole [debug0] disabled printk: bootconsole [debug0] disabled Calibrating delay loop... 9.61 BogoMIPS (lpj=48064) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) devtmpfs: initialized random: get_random_u32 called from bucket_table_alloc.isra.27+0x68/0x194 with crng_init=0 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 256 (order: -1, 3072 bytes, linear) NET: Registered protocol family 16 Data read fault at 0x00000000 in Super Data (pc=0x8a6a) BAD KERNEL BUSERR Oops: 00000000 Modules linked in: PC: [<00008a6a>] via_flush_cache+0x12/0x2c SR: 2700 SP: 01c1fe3c a2: 01c24000 d0: 00001119 d1: 0000000c d2: 00012000 d3: 0000000f d4: 01c06840 d5: 00033b92 a0: 00000000 a1: 00000000 Process swapper (pid: 1, task=01c24000) Frame format=B ssw=0755 isc=0200 isb=fff7 daddr=00000000 dobuf=01c1fed0 baddr=00008a6e dibuf=0000004e ver=f Stack from 01c1fec4: 01c1fed0 00007d7e 00010080 01c1fedc 0000792e 00000001 01c1fef4 00006b40 01c80000 00040000 00000006 00000003 01c1ff1c 004a545e 004ff200 00040000 00000000 00000003 01c06840 00033b92 004a5410 004b6c88 01c1ff84 000021e2 00000073 00000003 01c06840 00033b92 0038507a 004bb094 004b6ca8 004b6c88 004b6ca4 004b6c88 000021ae 00020002 00000000 01c0685d 00000000 01c1ffb4 0049f938 00409c85 01c06840 0045bd40 00000073 00000002 00000002 00000000 Call Trace: [<00007d7e>] mac_cache_card_flush+0x12/0x1c [<00010080>] fix_dnrm+0x2/0x18 [<0000792e>] cache_push+0x46/0x5a [<00006b40>] arch_dma_prep_coherent+0x60/0x6e [<00040000>] switched_to_dl+0x76/0xd0 [<004a545e>] dma_atomic_pool_init+0x4e/0x188 [<00040000>] switched_to_dl+0x76/0xd0 [<00033b92>] parse_args+0x0/0x370 [<004a5410>] dma_atomic_pool_init+0x0/0x188 [<000021e2>] do_one_initcall+0x34/0x1be [<00033b92>] parse_args+0x0/0x370 [<0038507a>] strcpy+0x0/0x1e [<000021ae>] do_one_initcall+0x0/0x1be [<00020002>] do_proc_dointvec_conv+0x54/0x74 [<0049f938>] kernel_init_freeable+0x126/0x190 [<0049f94c>] kernel_init_freeable+0x13a/0x190 [<004a5410>] dma_atomic_pool_init+0x0/0x188 [<00041798>] complete+0x0/0x3c [<000b9b0c>] kfree+0x0/0x20a [<0038df98>] schedule+0x0/0xd0 [<0038d604>] kernel_init+0x0/0xda [<0038d610>] kernel_init+0xc/0xda [<0038d604>] kernel_init+0x0/0xda [<00002d38>] ret_from_kernel_thread+0xc/0x14 Code: 0000 2079 0048 10da 2279 0048 10c8 d3c8 <1011> 0200 fff7 1280 d1f9 0048 10c8 1010 0000 0008 1080 4e5e 4e75 4e56 0000 2039 Disabling lock debugging due to kernel taint Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b Thanks to Stan Johnson for capturing the console log and running git bisect. Git bisect said commit 8e3a68fb55e0 ("dma-mapping: make dma_atomic_pool_init self-contained") is the first "bad" commit. I don't know why. Perhaps mach_l2_flush first became reachable with that commit. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-and-tested-by: Stan Johnson Signed-off-by: Finn Thain Cc: Joshua Thompson Link: https://lore.kernel.org/r/b8bbeef197d6b3898e82ed0d231ad08f575a4b34.1589949122.git.fthain@telegraphics.com.au Signed-off-by: Geert Uytterhoeven Signed-off-by: Sasha Levin

m68k: mac: Revisit floppy disc controller base addresses

2019-08-19T11:24:10Z

Rename floppy_type macros to make them more consistent with the scsi_type macros, which are named after classes of models with similar memory maps. The MAC_FLOPPY_OLD symbol is introduced to change the relevant base address from 0x50F00000 to 0x50000000 (consistent with MAC_SCSI_OLD). The documentation for LC-class machines has the IO devices at offsets from $50F00000. Use these addresses for MAC_FLOPPY_LC (consistent with MAC_SCSI_LC) because they may not be aliased elsewhere in the memory map. Add comments with controller type information from 'Designing Cards and Drivers for the Macintosh Family', relevant Developer Notes and http://mess.redump.net/mess/driver_info/mac_technical_notes Adopt phys_addr_t to avoid type casts. Signed-off-by: Finn Thain Tested-by: Stan Johnson Acked-by: Laurent Vivier Signed-off-by: Geert Uytterhoeven

Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi

2019-07-11T22:14:01Z

Pull SCSI updates from James Bottomley: "This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs, mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the removal of the osst driver (I heard from Willem privately that he would like the driver removed because all his test hardware has failed). Plus number of minor changes, spelling fixes and other trivia. The big merge conflict this time around is the SPDX licence tags. Following discussion on linux-next, we believe our version to be more accurate than the one in the tree, so the resolution is to take our version for all the SPDX conflicts" Note on the SPDX license tag conversion conflicts: the SCSI tree had done its own SPDX conversion, which in some cases conflicted with the treewide ones done by Thomas & co. In almost all cases, the conflicts were purely syntactic: the SCSI tree used the old-style SPDX tags ("GPL-2.0" and "GPL-2.0+") while the treewide conversion had used the new-style ones ("GPL-2.0-only" and "GPL-2.0-or-later"). In these cases I picked the new-style one. In a few cases, the SPDX conversion was actually different, though. As explained by James above, and in more detail in a pre-pull-request thread: "The other problem is actually substantive: In the libsas code Luben Tuikov originally specified gpl 2.0 only by dint of stating: * This file is licensed under GPLv2. In all the libsas files, but then muddied the water by quoting GPLv2 verbatim (which includes the or later than language). So for these files Christoph did the conversion to v2 only SPDX tags and Thomas converted to v2 or later tags" So in those cases, where the spdx tag substantially mattered, I took the SCSI tree conversion of it, but then also took the opportunity to turn the old-style "GPL-2.0" into a new-style "GPL-2.0-only" tag. Similarly, when there were whitespace differences or other differences to the comments around the copyright notices, I took the version from the SCSI tree as being the more specific conversion. Finally, in the spdx conversions that had no conflicts (because the treewide ones hadn't been done for those files), I just took the SCSI tree version as-is, even if it was old-style. The old-style conversions are perfectly valid, even if the "-only" and "-or-later" versions are perhaps more descriptive. * tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (185 commits) scsi: qla2xxx: move IO flush to the front of NVME rport unregistration scsi: qla2xxx: Fix NVME cmd and LS cmd timeout race condition scsi: qla2xxx: on session delete, return nvme cmd scsi: qla2xxx: Fix kernel crash after disconnecting NVMe devices scsi: megaraid_sas: Update driver version to 07.710.06.00-rc1 scsi: megaraid_sas: Introduce various Aero performance modes scsi: megaraid_sas: Use high IOPS queues based on IO workload scsi: megaraid_sas: Set affinity for high IOPS reply queues scsi: megaraid_sas: Enable coalescing for high IOPS queues scsi: megaraid_sas: Add support for High IOPS queues scsi: megaraid_sas: Add support for MPI toolbox commands scsi: megaraid_sas: Offload Aero RAID5/6 division calculations to driver scsi: megaraid_sas: RAID1 PCI bandwidth limit algorithm is applicable for only Ventura scsi: megaraid_sas: megaraid_sas: Add check for count returned by HOST_DEVICE_LIST DCMD scsi: megaraid_sas: Handle sequence JBOD map failure at driver level scsi: megaraid_sas: Don't send FPIO to RL Bypass queue scsi: megaraid_sas: In probe context, retry IOC INIT once if firmware is in fault scsi: megaraid_sas: Release Mutex lock before OCR in case of DCMD timeout scsi: megaraid_sas: Call disable_irq from process IRQ poll scsi: megaraid_sas: Remove few debug counters from IO path ...

scsi: mac_scsi: Enable PDMA on Mac IIfx

2019-06-20T19:37:03Z

Add support for Apple's custom "SCSI DMA" chip. This patch doesn't make use of its DMA capability. Just the PDMA capability is sufficient to improve sequential read throughput by a factor of 5. Cc: Michael Schmitz Cc: Joshua Thompson Cc: Geert Uytterhoeven Signed-off-by: Finn Thain Tested-by: Stan Johnson Tested-by: Michael Schmitz Acked-by: Geert Uytterhoeven Signed-off-by: Martin K. Petersen

treewide: Add SPDX license identifier - Makefile/Kconfig

2019-05-21T08:50:46Z

Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner Signed-off-by: Greg Kroah-Hartman

treewide: Add SPDX license identifier for missed files

2019-05-21T08:50:45Z

Add SPDX license identifiers to all files which: - Have no license information of any form - Have EXPORT_.*_SYMBOL_GPL inside which was used in the initial scan/conversion to ignore the file These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner Signed-off-by: Greg Kroah-Hartman