kernel.git/arch/arm/configs, branch linux-6.0.y

ARM: configs: at91: remove CONFIG_MICROCHIP_PIT64B

2022-08-29T11:26:14Z

Since commit f611af4c3bfa ("ARM: at91: Kconfig: implement PIT64B selection") there is no need to explicitly select PIT64B. Fixes: f611af4c3bfa ("ARM: at91: Kconfig: implement PIT64B selection") Signed-off-by: Claudiu Beznea Link: https://lore.kernel.org/r/20220826083927.3107272-2-claudiu.beznea@microchip.com

Merge tag 'usb-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

2022-08-04T18:41:28Z

Pull USB / Thunderbolt updates from Greg KH: "Here is the big set of Thunderbolt and USB changes for 6.0-rc1. Lots of little things here, nothing major, just constant development on some new hardware support and cleanups of older drivers. Highlights are: - lots of typec changes and improvements for new hardware - new gadget controller driver - thunderbolt support for new hardware - the normal set of new usb-serial device ids and cleanups - loads of dwc3 controller fixes and improvements - mtu3 driver updates - testusb fixes for longtime issues (not many people use this tool it seems.) - minor driver fixes and improvements over the USB tree - chromeos platform driver changes were added and then reverted as they depened on some typec changes, but the cross-tree merges caused problems so they will come back later through the platform tree. All of these have been in linux-next for a while now with no reported issues" * tag 'usb-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (193 commits) usb: misc: onboard_usb_hub: Remove duplicated power_on delay usb: misc: onboard_usb_hub: Add TI USB8041 hub support usb: misc: onboard_usb_hub: Add reset-gpio support USB: usbsevseg: convert sysfs snprintf to sysfs_emit dt-bindings: usb: Add binding for TI USB8041 hub controller ARM: multi_v7_defconfig: enable USB onboard HUB driver ARM: dts: stm32: add support for USB2514B onboard hub on stm32mp15xx-dkx usb: misc: onboard-hub: add support for Microchip USB2514B USB 2.0 hub dt-bindings: usb: generic-ehci: allow usb-hcd schema properties usb: typec: ucsi: stm32g0: add bootloader support usb: typec: ucsi: stm32g0: add support for stm32g0 controller dt-bindings: usb: typec: add bindings for stm32g0 controller usb: typec: ucsi: Acknowledge the GET_ERROR_STATUS command completion usb: cdns3: change place of 'priv_ep' assignment in cdns3_gadget_ep_dequeue(), cdns3_gadget_ep_enable() usb/chipidea: fix repeated words in comments usb: renesas-xhci: Do not print any log while fw verif success usb: typec: retimer: Add missing id check in match callback USB: xhci: Fix comment typo usb/typec/tcpm: fix repeated words in comments usb/musb: fix repeated words in comments ...

Merge tag 'efi-efivars-removal-for-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi

2022-08-03T21:41:36Z

Pull efivars sysfs interface removal from Ard Biesheuvel: "Remove the obsolete 'efivars' sysfs based interface to the EFI variable store, now that all users have moved to the efivarfs pseudo file system, which was created ~10 years ago to address some fundamental shortcomings in the sysfs based driver. Move the 'business logic' related to which EFI variables are important and may affect the boot flow from the efivars support layer into the efivarfs pseudo file system, so it is no longer exposed to other parts of the kernel" * tag 'efi-efivars-removal-for-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi: efi: vars: Move efivar caching layer into efivarfs efi: vars: Switch to new wrapper layer efi: vars: Remove deprecated 'efivars' sysfs interface

Merge tag 'arm-boardfiles-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

2022-08-02T15:35:17Z

Pull ARM boardfile deprecation from Arnd Bergmann: "Over the past ten years, new machine support was based on device tree, and an initial set of about 400 boards using ATAGS with boardfile for booting were grandfathered in, with about half of them either removed or converted to DT over time. Based on the recent mailing list discussion I started, I have now turned the findings into a set of patches that marks most board files as 'depends on UNUSED_BOARD_FILES', leaving only 38 of the 196 boards. For the boards that are marked as unused, there are two final chances for potential users: The removal is scheduled to take place after the longterm stable kernel at the end of 2022, so users can stay on that version for another few years, and if anyone still has one of these machines and is planning to keep updating kernels beyond that version, they can speak up now to have their boards taken off the list again. Waiting for the LTS release also makes sure that there will be at least one longterm kernel that contains the recent multiplatform conversion along while still supporting all legacy boards. The short summary of the current status is: - The s3c24xx, cns3xxx, iop32x and mv78xx0 platforms have no known users and will be removed entirely. - The mmp and davinci platforms have DT support for the important machines and will become DT-only after this. - s3c64xx, dove, orion5x, and pxa keep some board files to allow those to be migrated over to DT more easily, but most board files are getting removed now. DT support on these platforms is partially working but requires changes to additional drivers for the other boards. - omap1, ep93xx, sa1100, footbridge and rpc have no DT support at the moment but have some boards with known users. Removing the board files that nobody uses should make it easier to try a DT conversion if anyone cares. There is no explicit timeline what happens with the boards that remain after this removal, but I expect to revisit this in the future, and with most boards gone, there will be a good time to do a treewide review of platform drivers that never gained DT support and have no remaining in-tree board files" Link: https://lore.kernel.org/linux-arm-kernel/CAK8P3a0Z9vGEQbVRBo84bSyPFM-LF+hs5w8ZA51g2Z+NsdtDQA@mail.gmail.com/ * tag 'arm-boardfiles-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: ARM: cns3xxx: add CONFIG_UNUSED_BOARD_FILES dependency ARM: iop32x: mark as unused ARM: s3c: mark most board files as unused ARM: omap1: add Kconfig dependencies for unused boards ARM: sa1100: mark most boards as unused ARM: footbridge: mark cats board for removal ARM: mmp: mark all board files for removal ARM: ep93xx: mark most board files as unused ARM: davinci: mark all ATAGS board files as unused ARM: orion: add ATAGS dependencies ARM: pxa: add Kconfig dependencies for ATAGS based boards ARM: add CONFIG_UNUSED_BOARD_FILES ARM: add ATAGS dependencies to non-DT platforms

Merge tag 'arm-newsoc-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

2022-08-02T15:29:18Z

Pull ARM new SoC support from Arnd Bergmann: "This adds initial support for two SoC families that have been under review for a while. In both cases, the origonal idea was to have a minimally functional version, but we ended up leaving out the clk drivers that are still under review and will be merged through the corresponding subsystem tree. The Nuvoton NPCM8xx is a 64-bit Baseboard Management Controller and based on the 32-bit NPCM7xx family but is now getting added to arch/arm64 as well. Sunplus SP7021, also known as Plus1, is a general-purpose System-in-Package design based on the 32-bit Cortex-A7 SoC on the main chip, plus an I/O chip and memory in the same" * tag 'arm-newsoc-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (25 commits) MAINTAINERS: rectify entry for ARM/NUVOTON NPCM ARCHITECTURE arm64: defconfig: Add Nuvoton NPCM family support arm64: dts: nuvoton: Add initial NPCM845 EVB device tree arm64: dts: nuvoton: Add initial NPCM8XX device tree arm64: npcm: Add support for Nuvoton NPCM8XX BMC SoC dt-bindings: arm: npcm: Add nuvoton,npcm845 GCR compatible string dt-bindings: arm: npcm: Add nuvoton,npcm845 compatible string dt-bindings: arm: npcm: Add maintainer reset: npcm: Add NPCM8XX support dt-bindings: reset: npcm: Add support for NPCM8XX reset: npcm: using syscon instead of device data ARM: dts: nuvoton: add reset syscon property dt-bindings: reset: npcm: add GCR syscon property dt-binding: clk: npcm845: Add binding for Nuvoton NPCM8XX Clock dt-bindings: watchdog: npcm: Add npcm845 compatible string dt-bindings: timer: npcm: Add npcm845 compatible string ARM: dts: Add Sunplus SP7021-Demo-V3 board device tree ARM: sp7021_defconfig: Add Sunplus SP7021 defconfig ARM: sunplus: Add initial support for Sunplus SP7021 SoC irqchip: Add Sunplus SP7021 interrupt controller driver ...

Merge tag 'arm-defconfig-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

2022-08-02T15:21:58Z

Pull ARM SoC defconfig updates from Arnd Bergmann: "This branch includes the usual updates to defconfig files, enabling additional driver support for the supported platforms. There is also a global refresh for all of them that reorders the lines according to the 'savedefconfig' output, but without removing lines that are no longer part of the refresh. I went through the most common removed lines to also address them while making sure to catch renamed options and add them back under the new name. The boardfile deprecation branch is based on top of this to avoid conflicts against removing the unused boardfile configs from the generic defconfig files" * tag 'arm-defconfig-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (24 commits) arm64: defconfig: Sync some configs with savedefconfig arm64: refresh defconfig file ARM: defconfig: kill remnants of CONFIG_LEDS ARM: defconfig: remove broken CONFIG_THUMB disables ARM: defconfig: address renamed CONFIG_DEBUG_INFO=y ARM: defconfig: remove stale CONFIG_ZBOOT_ROM entries ARM: defconfig: remove irda remnants ARM: refresh defconfig files arm64: defconfig: Demote Qualcomm USB PHYs to modules arm64: defconfig: Enable Qualcomm SC8280XP providers ARM: multi_v7_defconfig: Update configs for BCM63138 arm64: defconfig: enable Qualcomm Bandwidth Monitor arm64: defconfig: Enable Allwinner built in CODECs arm64: defconfig: Enable qcom interconnect drivers arm64: defconfig: Enable qcom ss & hs usb phy arm64: defconfig: enable Qualcomm LPG leds driver arm64: defconfig: Enable gpio-fan support arm64: defconfig: Enable DRM_V3D ARM: configs: Enable DRM_V3D arm64: defconfig: Enable R8A779G0 SoC ...

ARM: multi_v7_defconfig: enable USB onboard HUB driver

2022-07-27T12:39:52Z

Enable the USB onboard HUB driver, used on STM32MP1 boards. Signed-off-by: Fabrice Gasnier Link: https://lore.kernel.org/r/20220726080708.162547-5-fabrice.gasnier@foss.st.com Signed-off-by: Greg Kroah-Hartman

ARM: cns3xxx: add CONFIG_UNUSED_BOARD_FILES dependency

2022-07-22T12:18:52Z

Krzysztof Halasa has kept the cns3xxx platform working for a long time but has moved away from working on it. The OpenWRT port was dropped in 2020, and support for the Gateworks Laguna platform never made it into the mainline kernel, which only supports the reference design. Further, the ARM11MPCore has an unresolved issue with instruction cache coherency, and removing support for the remaining platforms using this core would be the easiest solution. Mark the entire platform as unused now, to be removed in early 2023 if no users show up. Cc: Krzysztof Halasa Link: https://lore.kernel.org/lkml/20210616152326.GG22278@shell.armlinux.org.uk/ Signed-off-by: Arnd Bergmann

ARM: iop32x: mark as unused

2022-07-22T12:18:52Z

The iop32x platform has recently been converted to be part of the multiplatform configuration, and it should be possible to keep it alive for longer by making it boot from devicetree like we did for the related ixp4xx platform. However, it appears that no users remain at this point, so just mark the entire platform depending on CONFIG_UNUSED_BOARD_FILES, with the intention of removing it in early 2023. If any users remain, please speak up now. Cc: Lennert Buytenhek Acked-by: Dan Williams Signed-off-by: Arnd Bergmann

ARM: s3c: mark most board files as unused

2022-07-22T12:18:52Z

The s3c24xx platform is already scheduled for removal in early 2023, with s3c64xx meeting the same fate a year later. Most of the s3c64xx board files appear to be unused, as the better maintained ones already got converted to DT. The main exception is the Wolfson Cragganmore board, which remains in use as the reference design for Wolfson/Cirrus devices. As the other boards get removed, this one stays around along with the DT based machines. The s3c6400_defconfig file now disables the unused boards, while the s3c24xx defconfig files all turn on CONFIG_UNUSED_BOARD_FILES to remain usable. Cc: Krzysztof Kozlowski Cc: Alim Akhtar Cc: linux-samsung-soc@vger.kernel.org Signed-off-by: Arnd Bergmann