kernel.git/arch/arm/configs, branch linux-4.15.y

ARM: sunxi_defconfig: Enable CMA

2018-01-19T15:08:08Z

The DRM driver most notably, but also out of tree drivers (for now) like the VPU or GPU drivers, are quite big consumers of large, contiguous memory buffers. However, the sunxi_defconfig doesn't enable CMA in order to mitigate that, which makes them almost unusable. Enable it to make sure it somewhat works. Cc: Signed-off-by: Maxime Ripard Signed-off-by: Arnd Bergmann

Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

2017-11-16T22:05:12Z

Pull ARM SoC platform updates from Arnd Bergmann: "Most of the commits are for defconfig changes, to enable newly added drivers or features that people have started using. For the changed lines lines, we have mostly cleanups, the affected platforms are OMAP, Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions. The largest single change is the introduction of the TI "sysc" bus driver, with the intention of cleaning up more legacy code. Two new SoC platforms get added this time: - Allwinner R40 is a modernized version of the A20 chip, now with a Quad-Core ARM Cortex-A7. According to the manufacturer, it is intended for "Smart Hardware" - Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family of chips meant for managed gigabit ethernet switches, based around a Cortex-A9 CPU. Finally, we gain SMP support for two platforms: Renesas R-Car E2 and Amlogic Meson8/8b, which were previously added but only supported uniprocessor operation" * tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (118 commits) ARM: multi_v7_defconfig: Select RPMSG_VIRTIO as module ARM: multi_v7_defconfig: enable CONFIG_GPIO_UNIPHIER arm64: defconfig: enable CONFIG_GPIO_UNIPHIER ARM: meson: enable MESON_IRQ_GPIO in Kconfig for meson8b ARM: meson: Add SMP bringup code for Meson8 and Meson8b ARM: smp_scu: allow the platform code to read the SCU CPU status ARM: smp_scu: add a helper for powering on a specific CPU dt-bindings: Amlogic: Add Meson8 and Meson8b SMP related documentation ARM: OMAP3: Delete an unnecessary variable initialisation in omap3xxx_hwmod_init() ARM: OMAP3: Use common error handling code in omap3xxx_hwmod_init() ARM: defconfig: select the right SX150X driver arm64: defconfig: Enable QCOM_IOMMU arm64: Add ThunderX drivers to defconfig arm64: defconfig: Enable Tegra PCI controller cpufreq: imx6q: Move speed grading check to cpufreq driver arm64: defconfig: re-enable Qualcomm DB410c USB ARM: configs: stm32: Add MDMA support in STM32 defconfig ARM: imx: Enable cpuidle for i.MX6DL starting at 1.1 bus: ti-sysc: Fix unbalanced pm_runtime_enable by adding remove bus: ti-sysc: mark PM functions as __maybe_unused ...

Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6

2017-11-14T18:52:09Z

Pull crypto updates from Herbert Xu: "Here is the crypto update for 4.15: API: - Disambiguate EBUSY when queueing crypto request by adding ENOSPC. This change touches code outside the crypto API. - Reset settings when empty string is written to rng_current. Algorithms: - Add OSCCA SM3 secure hash. Drivers: - Remove old mv_cesa driver (replaced by marvell/cesa). - Enable rfc3686/ecb/cfb/ofb AES in crypto4xx. - Add ccm/gcm AES in crypto4xx. - Add support for BCM7278 in iproc-rng200. - Add hash support on Exynos in s5p-sss. - Fix fallback-induced error in vmx. - Fix output IV in atmel-aes. - Fix empty GCM hash in mediatek. Others: - Fix DoS potential in lib/mpi. - Fix potential out-of-order issues with padata" * 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (162 commits) lib/mpi: call cond_resched() from mpi_powm() loop crypto: stm32/hash - Fix return issue on update crypto: dh - Remove pointless checks for NULL 'p' and 'g' crypto: qat - Clean up error handling in qat_dh_set_secret() crypto: dh - Don't permit 'key' or 'g' size longer than 'p' crypto: dh - Don't permit 'p' to be 0 crypto: dh - Fix double free of ctx->p hwrng: iproc-rng200 - Add support for BCM7278 dt-bindings: rng: Document BCM7278 RNG200 compatible crypto: chcr - Replace _manual_ swap with swap macro crypto: marvell - Add a NULL entry at the end of mv_cesa_plat_id_table[] hwrng: virtio - Virtio RNG devices need to be re-registered after suspend/resume crypto: atmel - remove empty functions crypto: ecdh - remove empty exit() MAINTAINERS: update maintainer for qat crypto: caam - remove unused param of ctx_map_to_sec4_sg() crypto: caam - remove unneeded edesc zeroization crypto: atmel-aes - Reset the controller before each use crypto: atmel-aes - properly set IV after {en,de}crypt hwrng: core - Reset user selected rng by writing "" to rng_current ...

ARM: multi_v7_defconfig: Select RPMSG_VIRTIO as module

2017-11-07T15:30:14Z

The RPMSG_VIRTIO is now user selectable option so we explicitly select it in multi_v7_defconfig. Till now RPMSG_VIRTIO was selected by ST_REMOTEPROC=m in multi_v7_defconfig. Signed-off-by: Anup Patel Acked-by: Bjorn Andersson Signed-off-by: Arnd Bergmann

ARM: configs: Stop selecting the old CESA driver

2017-11-03T13:50:48Z

A new driver has been developed to support the CESA IP. Switch remaining users of the old driver to the new driver in order to remove the old one. Signed-off-by: Boris Brezillon Signed-off-by: Herbert Xu

ARM: multi_v7_defconfig: enable CONFIG_GPIO_UNIPHIER

2017-10-30T13:42:05Z

Enable the GPIO controller driver used for UniPhier SoC family. Signed-off-by: Masahiro Yamada Signed-off-by: Arnd Bergmann

Merge tag 'arm-soc/for-4.15/defconfig' of http://github.com/Broadcom/stblinux into next/soc

2017-10-30T10:02:01Z

Pull "Broadcom defconfig changes for 4.15" from Florian Fainelli: This pull request contains Broadcom ARM-based SoCs multi_v7_defconfig file updates for 4.15, please pull the following: - Florian enables the Broadcom Hurricane 2 SoC in multi_v7_defconfig (CONFIG_ARCH_BCM_HR2) * tag 'arm-soc/for-4.15/defconfig' of http://github.com/Broadcom/stblinux: ARM: multi_v7_defconfig: Enable CONFIG_ARCH_BCM_HR2

Merge tag 'keystone_config_4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/soc

2017-10-30T10:00:01Z

Pull "ARM: Keystone config update for 4.15" from Santosh Shilimkar: ARM: Enable PWM driver config * tag 'keystone_config_4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone: ARM: configs: keystone: Enable TIECAP PWM driver

Merge tag 'amlogic-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/soc

2017-10-30T09:58:30Z

Pull "Amlogic: defconfig updates for v4.15" from Kevin Hilman: - enable SDIO/MMC controller * tag 'amlogic-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic: ARM: multi_v7_defconfig: enable the Meson MX SDIO/MMC controller

Merge tag 'imx-defconfig-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/soc

2017-10-30T09:43:07Z

Pull "i.MX defconfig updates for 4.15" from Shawn Guo: - Turn on DRM_DW_HDMI_CEC option to get HDMI CEC support. - Enable MUX_MMIO to get ADV7180 probe on Gateworks GW51xx boards. * tag 'imx-defconfig-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: ARM: imx_v6_v7_defconfig: Select the CEC driver ARM: imx_v6_v7_defconfig: Select CONFIG_MUX_MMIO