kernel.git/Documentation/devicetree/bindings/net/wireless, branch linux-4.16.y

Merge ath-next from git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.git

2017-12-14T16:38:48Z

ath.git patches for 4.16. Major changes: ath10k * enable multiqueue support for all hw using mac80211 wake_tx_queue op * new Kconfig option ATH10K_SPECTRAL to save RAM * show tx stats on QCA9880 * new qcom,ath10k-calibration-variant DT entry * WMI layer support for wcn3990 ath9k * new Kconfig option ATH9K_COMMON_SPECTRAL to save RAM wcn36xx * hardware scan offload support wil6210 * run-time PM support when interface is down

dt: bindings: add new dt entry for ath10k calibration variant

2017-12-14T15:27:48Z

The bus + bmi-chip-id + bmi-board-id is not enough to identify the correct board data file on QCA4019 based devices. Multiple different boards share the same values. Only the original reference designs can currently be identified and loaded from the board-2.bin. But these will not result in the correct calibration data when combined with the pre-calibration data from the device. An additional "variant" information has to be provided (via SMBIOS or DT) to select the correct board data for a design which was modified by an ODM. Signed-off-by: Sven Eckelmann Signed-off-by: Kalle Valo

dt-bindings: net: add mt76 wireless device binding

2017-12-07T13:35:54Z

Add documentation describing how device tree can be used to configure wireless chips supported by the mt76 driver. Signed-off-by: Felix Fietkau Signed-off-by: Kalle Valo

dt-bindings: Remove leading zeros from bindings notation

2017-11-09T23:05:05Z

Improve the binding example by removing all the leading zeros to fix the following dtc warnings: Warning (unit_address_format): Node /XXX unit name should not have leading 0s Converted using the following command: perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find ./Documentation/devicetree/bindings "*.txt"` Some unnecessary changes were manually fixed. Signed-off-by: Marco Franchi Signed-off-by: Rob Herring

dt-bindings: Remove "status" from examples

2017-09-05T15:03:06Z

Pretty much any node can have a status property, so it doesn't need to be in examples. Converted with the following command and removed examples with SoC and board specific splits: git grep -l -E 'status.*=.*' Documentation/devicetree/ | xargs sed -i -E '/\sstatus.*=.*"(disabled|ok|okay)/d' Acked-by: Mark Rutland Signed-off-by: Rob Herring

Merge tag 'devicetree-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux

2017-07-07T17:37:54Z

Pull DeviceTree updates from Rob Herring: - vsprintf format specifier %pOF for device_node's. This will enable us to stop storing the full node names. Conversion of users will happen next cycle. - Update documentation to point to DT specification instead of ePAPR. - Split out graph and property functions to a separate file. - New of-graph functions for ALSA - Add vendor prefixes for RISC-V, Linksys, iWave Systems, Roofull, Itead, and BananaPi. - Improve dtx_diff utility filename printing. * tag 'devicetree-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (32 commits) of: document /sys/firmware/fdt dt-bindings: Add RISC-V vendor prefix vsprintf: Add %p extension "%pOF" for device tree of: find_node_by_full_name rewrite to compare each level of: use kbasename instead of open coding dt-bindings: thermal: add file extension to brcm,ns-thermal of: update ePAPR references to point to Devicetree Specification scripts/dtc: dtx_diff - Show real file names in diff header of: detect invalid phandle in overlay of: be consistent in form of file mode of: make __of_attach_node() static of: address.c header comment typo of: fdt.c header comment typo of: make of_fdt_is_compatible() static dt-bindings: display-timing.txt convert non-ascii characters to ascii Documentation: remove overlay-notes reference to non-existent file dt-bindings: usb: exynos-usb: Add missing required VDD properties dt-bindings: Add vendor prefix for Linksys MAINTAINERS: add device tree ABI documentation file of: Add vendor prefix for iWave Systems Technologies Pvt. Ltd ...

wlcore: add wl1285 compatible

2017-06-13T07:05:40Z

Motorola Droid 4 uses a WL 1285C. With differences between chips not being public let's add explicit binding for wl1285 instead of relying on wl1283 being very similar. Reviewed-by: Rob Herring Acked-by: Kalle Valo Acked-by: Tony Lindgren Signed-off-by: Sebastian Reichel Signed-off-by: Kalle Valo

dt-binding: net: wireless: fix node name in the BCM43xx example

2017-05-19T01:57:33Z

The example in the BCM43xx documentation uses "brcmf" as node name. However, wireless devices should be named "wifi" instead. Fix this to make sure that .dts authors can simply use the documentation as reference (or simply copy the node from the documentation and then adjust only the board specific bits). Signed-off-by: Martin Blumenstingl Acked-by: Arend van Spriel Signed-off-by: Rob Herring

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

2017-02-22T18:15:09Z

Pull networking updates from David Miller: "Highlights: 1) Support TX_RING in AF_PACKET TPACKET_V3 mode, from Sowmini Varadhan. 2) Simplify classifier state on sk_buff in order to shrink it a bit. From Willem de Bruijn. 3) Introduce SIPHASH and it's usage for secure sequence numbers and syncookies. From Jason A. Donenfeld. 4) Reduce CPU usage for ICMP replies we are going to limit or suppress, from Jesper Dangaard Brouer. 5) Introduce Shared Memory Communications socket layer, from Ursula Braun. 6) Add RACK loss detection and allow it to actually trigger fast recovery instead of just assisting after other algorithms have triggered it. From Yuchung Cheng. 7) Add xmit_more and BQL support to mvneta driver, from Simon Guinot. 8) skb_cow_data avoidance in esp4 and esp6, from Steffen Klassert. 9) Export MPLS packet stats via netlink, from Robert Shearman. 10) Significantly improve inet port bind conflict handling, especially when an application is restarted and changes it's setting of reuseport. From Josef Bacik. 11) Implement TX batching in vhost_net, from Jason Wang. 12) Extend the dummy device so that VF (virtual function) features, such as configuration, can be more easily tested. From Phil Sutter. 13) Avoid two atomic ops per page on x86 in bnx2x driver, from Eric Dumazet. 14) Add new bpf MAP, implementing a longest prefix match trie. From Daniel Mack. 15) Packet sample offloading support in mlxsw driver, from Yotam Gigi. 16) Add new aquantia driver, from David VomLehn. 17) Add bpf tracepoints, from Daniel Borkmann. 18) Add support for port mirroring to b53 and bcm_sf2 drivers, from Florian Fainelli. 19) Remove custom busy polling in many drivers, it is done in the core networking since 4.5 times. From Eric Dumazet. 20) Support XDP adjust_head in virtio_net, from John Fastabend. 21) Fix several major holes in neighbour entry confirmation, from Julian Anastasov. 22) Add XDP support to bnxt_en driver, from Michael Chan. 23) VXLAN offloads for enic driver, from Govindarajulu Varadarajan. 24) Add IPVTAP driver (IP-VLAN based tap driver) from Sainath Grandhi. 25) Support GRO in IPSEC protocols, from Steffen Klassert" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1764 commits) Revert "ath10k: Search SMBIOS for OEM board file extension" net: socket: fix recvmmsg not returning error from sock_error bnxt_en: use eth_hw_addr_random() bpf: fix unlocking of jited image when module ronx not set arch: add ARCH_HAS_SET_MEMORY config net: napi_watchdog() can use napi_schedule_irqoff() tcp: Revert "tcp: tcp_probe: use spin_lock_bh()" net/hsr: use eth_hw_addr_random() net: mvpp2: enable building on 64-bit platforms net: mvpp2: switch to build_skb() in the RX path net: mvpp2: simplify MVPP2_PRS_RI_* definitions net: mvpp2: fix indentation of MVPP2_EXT_GLOBAL_CTRL_DEFAULT net: mvpp2: remove unused register definitions net: mvpp2: simplify mvpp2_bm_bufs_add() net: mvpp2: drop useless fields in mvpp2_bm_pool and related code net: mvpp2: remove unused 'tx_skb' field of 'struct mvpp2_tx_queue' net: mvpp2: release reference to txq_cpu[] entry after unmapping net: mvpp2: handle too large value in mvpp2_rx_time_coal_set() net: mvpp2: handle too large value handling in mvpp2_rx_pkts_coal_set() net: mvpp2: remove useless arguments in mvpp2_rx_{pkts, time}_coal_set ...

devicetree: document new marvell-8xxx and pwrseq-sd8787 options

2017-02-13T12:20:33Z

Cc: Rob Herring Cc: devicetree@vger.kernel.org Signed-off-by: Matt Ranostay Signed-off-by: Ulf Hansson Acked-by: Rob Herring